Travel Mandolele / Bouzoukulele / GDAE Travelele
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A quiet 4-stringed instrument with mandolin fret spacing
- Rating
- 0 / 5
- Likes
- 32
- Downloads
- 81
- Makes
- 0
- Views
- 678
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Music
- License
- Creative Commons — Attribution — Noncommercial
This is a Travelele purpose-built to be tuned in GDAE or GDAD.
I'm an Irish Bouzouki player and wanted something I could take on work trips to practice. The Travelele was ideal: quiet, portable. But it wasn't set up to be tuned in GDAD, so I did some research and made some modifications!
This remix contains a beefier truss rod to handle more tension, and a special bridge for the right size strings. There's also a slot in the body to hold a pick. Lastly, it adds the soundboard, in case you want to amplify yourself a little.
Parts Needed
4× Ukulele Friction Tuning Pegs (like these)
1× 028 Wound Nylon String (like this)
1× 035 Nylon String (like this)
1× 024 Nylon String (like this)
1× 017 Nylon String (like this)
1× M3×25 hex head screw
1× M3 nut (hex or square: either works)
1× washer to go under the screw head
A bit of poster putty (like this)
Do not use a philips head screw: you will strip it trying to tension the neck.
Printing
Use PLA for its rigidity and density.
Add supports for the body where the neck attaches, and for the neck where the truss rod goes in and where the screw goes in. 15% infill was fine for me, but the higher the infill, the heavier/louder it will be. Bear in mind that "louder" is relative here: I didn't feel like 100% was worth it for the modest gain.
Definitely print the truss rod at 100% infill, though! It needs all the strength you can give it, especially when you start smashing it with the tensioning screw.
If you want to get really fancy, you can use your MMU to paint on fret markers. I just used a sharpie.
Assembly
Place the neck on the body: it will bend up. Place the truss rod in. Drop the nut into the hole in the truss rod, then slide the washer over the screw and place them in the hole. You may need needle-nosed pliers to match the screw up to the nut. Screw it down until the neck is more or less coplanar with the body. You'll be screwing it in further after adding the strings.
Put the tuners on. The order of layers, from the inside to outside of the body, should be post, metal shield, felt disc, plastic instrument, tuning head, screw. Tighten the screw just enough to add some friction to turning the tuner. You'll tighten it more when you tune up.
The bridge is asymmetrical, but the nut is not. Bridge orientation will depend on whether you want a left or right handed instrument.
Look up how to string a Ukulele: my photos might help.
As you tune the strings, the neck will bend forward. Use the truss rod screw to get it flat again.
Put some putty into the slot on the body. You probably only need a ball about 1mm in diameter, but adding more won't hurt. Work it in with a pick. The idea is to get enough putty into the crack that it will hold the pick in place during transit.
Tuning / Intonation
You may never get this perfectly in tune. Try to remember it's a practice instrument, not meant to be heard by anyone but the player. Your goal is "close enough to in tune".
The only way to change intonation is with the truss rod screw. If fretted notes are too sharp, screw in tighter. If the strings are buzzing against the frets, unscrew.
As you tension the strings, the tuner may lose friction and the string lose tension. Tighten the screw in the tuner to increase friction and keep the tension in the string.
The strings I listed will let you tune to GDAD or GDAE.
Caution: Stripping the nylon core
As you tension strings, you may hear a "pop". This is the string getting caught against a printing layer, and it's working against you getting the instrument in tune properly. If you have a string that pops as you tension it, then stops popping as you fine tune it, back the tuning out and try retensioning quickly. The wound strings can get caught on the printing layers and strip the nylon core out. I've found Aquila strings are especially prone to doing this.
Making It Louder / Quieter
The optional soundboard can be popped in and out of the back of the instrument to add a bit of volume. Push it out when you're in quiet places like the waiting room for your allergy shot. If you just barely hear the instrument, people around you (probably) won't hear it at all.
Adding a Pickup
The Travelele has a hole in the back where you can insert a pickup under the bridge. I have no idea why anyone would want to do this: the instrument does not play in tune. But if you're a weirdo and add a pickup, please leave a comment letting us know how it went!
Answering Questions about it
If you play this in front of other people, the first question is going to be "what is that". You're going to have to think of a name. Here are some I've used:
Travel Irish Bouzouki - Because the word "Irish" is here, it leads the discussion into what kind of music I play
Bouzoukulele - It's so fun to say, but only musicians are going to understand why this term is so clever
Crapolin - Ha ha ha
Travelele - Honor the inventor's name
Wall Mount / Hanger
I've included a wall mount model: print with supports. You can stick it to the wall with command strips: I wouldn't advise using screws.
This is simple the Odbix Ukulele mount, scaled down a bit, with a negative space Bouzoukulele scaled to 105%. I don't know if this is going to work outside of PrusaSlicer. If you need an STL, please let me know, and I'll redo the part in Tinkercad.
Plectrum/Pick
If you want your pick to match your instrument, these work pretty well. 0.6mm thick is about the same stiffness as a 0.6mm Tortex pick.