Voron 2.4 Under-bed Chamber Heater 5015 Blower Fan Mounts
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Mounts for 5015 blower fans to pull heat from the bottom of the heated bed to control the chamber temperature.
- Rating
- 0 / 5
- Likes
- 15
- Downloads
- 39
- Makes
- 0
- Views
- 447
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Voron Parts & Upgrades
- License
- Creative Commons — Attribution
Mounts for 5015 blowers for Voron 2.4 350mm bed printer with kinematic bed mounts installed. Without the kinematic bed mounts, there probably isn't enough clearance under the bed, so either use a lower fan tilt angle or a different mount entirely in that case. Tested on 350mm LDO Rev. D kit. This angles the fans slightly upward (tilt=10°, configurable in OpenSCAD file) for better airflow across the bottom of the bed to aid in heating/maintaining a constant chamber temperature throughout a print. See https://www.printables.com/model/1612950-voron-24-under-bed-chamber-heater-air-deflector for a airflow deflector to help recirculate the air in the chamber. With both these parts, I am able to keep the chamber within ±0.2°C of setpoint temperature on my printer.
When using the chamber heater, It certainly helps to bring your bed up to temperature and let it come to an equilibrium before the under-bed fans are turned on, otherwise there is a significant drop in bed temperature which can lead to a Klipper shutdown and unstable bed temperature. I have to leave my bed at setpoint temperature (after ramp-up) for about 10 minutes before turning on the blowers. I then let the chamber get to its temperature setpoint. For ABS I run the bed at 110°C and set the chamber at 57°C. This allows the temperature of the bed and the chamber to get to a steady-state. Keep in mind that even with ABS you will probably need to put the part fan on for the entire print, especially for bridged structures. I keep the fan off for the first 3 layers and have it ramp to 100% by layer 5, but you will likely have to optimize this for your particular printer and filament.
Required Parts:
4x 5015 blowers
16x M4 inserts
16x M4x12mm button-head screws to mount fans
2x 5-port Wago terminals
Print Settings:
5 perimeters
5 top/bottom layers
no supports
30% gyroid infill
I printed with ABS, but anything that can handle chamber temperatures should work
Changes to printer.cfg file in Klipper:
Comment out section where chamber temperature sensor is configured: (yours is probably different)
#[temperature_sensor chamber_temp]
### Chamber Temperature - T1
#sensor_type: ATC Semitec 104NT-4-R025H42G
#sensor_pin: nhk:gpio28
#min_temp: 0
#max_temp: 100
#gcode_id: chamber_thNow add a section to the fans section: (adapt yours using the part you just commented out) In my case it is connected to PB7 on a Leviathan controller board. Change max_power from 0.5 (50%) to a lower number if the heated bed temperature can't maintain setpoint. Keep in mind that you will have to manually tune the PID loop, these values worked well for my system and are probably a decent starting point. Google "Ziegler-Nichols PID tuning" for an algorithm for optimizing the parameters.
# Needed to modify ~/klipper/klippy/extras/temperature_fan.py to make PID loop positive acting (heating)
# instead of its default behavior of negative acting (cooling)
[temperature_fan chamber]
pin: PB7 # Your fan PWM pin
max_power: 0.50 # Max 50% speed; If heated bed doesn't keep up, lower this!
off_below: 0.00 # Min 0% speed; edit here (anything below threshold, the fan is off)
shutdown_speed: 0.0
kick_start_time: 0.5 # Helps fans spin up from 0%
#hardware_pwm: true # Try this first for ~10-20 kHz (silent, no pulsing); if fans don't spin reliably, set to false and use cycle_time below
cycle_time: 0.01 # 100 Hz PWM frequency (seems to work best with my cheap fans)
#cycle_time: 0.0001 # 10 kHz PWM frequency
#cycle_time: 0.00005 # 20 kHz PWM frequency
sensor_type: ATC Semitec 104NT-4-R025H42G
sensor_pin: nhk:gpio28
min_temp: 0
max_temp: 75
control: pid
pid_Kp: 80.0 # Proportional control
pid_Ki: 1.00 # Integral control
pid_Kd: 200.0 # Derivative control
target_temp: 0 # Starts off
min_speed: 0.0 # Allows clamping to 0% when below setpoint
max_speed: 1.0 # Full range up to max_powerRemap M141: (this way we can wait until the bed is at temperature before turning on fans)
[gcode_macro M141]
gcode:
{action_respond_info("Chamber target %s noted; fans will start after bed is at setpoint" % params.S|default("unset"))}Add line to START_PRINT macro:
Add M190 S{BED} after heated bed to let the bed get to its setpoint, then add SET_TEMPERATURE_FAN_TARGET TEMPERATURE_FAN=chamber TARGET={CHAMBER} to set the chamber temperature. Optionally you can add M191 S{CHAMBER} to wait for the chamber to get to temperature before starting the print. Make sure you also have the {% set CHAMBER = params.CHAMBER|default(0)|float %} line at the beginning of the macro. An example of my PRINT_START command is below:
[gcode_macro PRINT_START]
# Use PRINT_START for the slicer starting script - please customize for your slicer of choice
gcode: #updated 2/18/2026 with bed heater routine
{% set BED = params.BED|default(60)|float %}
{% set EXTRUDER = params.EXTRUDER|default(200)|float %}
{% set CHAMBER = params.CHAMBER|default(0)|float %}TURN_OFF_HEATERS # Reset everything safely
SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={BED}
M190 S{BED} # Wait for bed to reach target
# Bed is now at setpoint → enable & control chamber fans
SET_TEMPERATURE_FAN_TARGET TEMPERATURE_FAN=chamber TARGET={CHAMBER}
# M191 S{CHAMBER} # Optional: uncomment if you want to wait for chamber to reach setpoint before purge/layers start (or just do a heat soak first)
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={EXTRUDER}
# end updated section from 2/18/2026
SET_PIN PIN=caselight VALUE=0.30
SET_LED LED="rgb_light" RED=0 GREEN=0 BLUE=0 WHITE=0.0627 SYNC=0 INDEX=2
SET_LED LED="rgb_light" RED=0 GREEN=0 BLUE=0 WHITE=0.0627 SYNC=0 INDEX=3 TRANSMIT=1
G32 ; home all axes
G90 ; absolute positioning
CLEAN_NOZZLE
G28 Z ; re-home axis after wipe
BED_MESH_CALIBRATE ; calibrate the bed mesh
;G1 Z20 F3000 ; move nozzle away from bed
CLEAN_NOZZLE
G92 E0 ; zero the extruder MJC
#G1 E28.0 F300 ; un-retract filament from print_end macro MJC #KAMP takes care of this during the purge
G92 E0 ; zero the extruder MJC
#VORON_PURGE ; Voron logo purge right before the print
LINE_PURGE ; Line purge right before the print</code></pre><p>Make sure your slicer sets the chamber temperature in the gcode, this is what I have for PrusaSlicer in printer->custom g-code: (all on one line)</p><pre><code>PRINT_START EXTRUDER=[first_layer_temperature[initial_tool]] BED=[first_layer_bed_temperature] CHAMBER=[chamber_temperature]</code></pre><h3>Changing <code>temperature_fan.py</code> to change from inverse PID to direct-acting PID:</h3><p>Default behavior of <code>temperature_fan.py</code> is meant for cooling using fans. Since we are heating the chamber with the fan, we need to invert the logic so it has a direct-acting response. Swapping the sign of the P, I and D constants does not work due to how the PID update is handled. The easiest solution is to rewrite the lines that calculate the PID output that make it direct-acting. <strong>Note:</strong> if there are other fans on the printer that are setup to use PID for cooling, these changes will break them!</p><p>If you treat it as a heater, you're stuck with ~1 Hz updates which is too slow to keep the fans running smoothly. This seems to be the only way to implement PID control, otherwise some custom g-code needs to be written or bang-bang control can be used, though it causes temperature fluctuations in both the chamber and the bed.</p><p>For Klipper v0.13.0-540 open <code>~/home/klipper/klippy/extras/temperature_fan.py</code> and make the following edits:</p><ul><li><p>Change the line <code>fan_speed = self.max_speed - pid / self.pwm_scale</code><br>to <code>fan_speed = (pid / self.pwm_scale) * self.max_speed</code><br>This fixes the PID response so the P,I and D settings can be positive in the <code>printer.cfg</code> file.</p></li><li><p>Change the line <code>self.min_speed = config.getfloat('min_speed', 0.3, below=self.max_speed)</code><br>to <code>self.min_speed = config.getfloat('min_speed', 0.0, below=self.max_speed)</code><br>This ensures the fan can truly go to 0% when the chamber is at/above setpoint</p></li></ul><p></p>
