Clamp - Universal motorcycle phone holder with vertical arm

First of all, kudos to Albatrog for the original design, check it out, it's really great work. 

I could not find any M6*18 around where I live, not even on ebay. So I had to modify the ASA mainsection to hold a M6*20 long nut. 

Because I was a bit afraid of holding the phone 'only' with the two TPU grippers, I added a vertical twerp for safety. I also include a version for M6*20 without the vertical arm and a new version of ASA_topsection. It just has the same chamfer like ASA_mainsection for aesthetic reasons.

A dummy part is also included, clamp in in the holder when riding without a phone to prevent loss of the TPU_holders. 

The NEW parts are thus: 

-) ASA_mainsection_wCutout_M6*20mm_nut (like original part but for M6*20mm long nut)

-) ASA_mainsection_wCutout_M6x20mm_nut_and_vertical_holder (like original part but with M6*20mm cutout AND vertical holder)

-) ASA_topsection_wChamfer

-) PETG_DUMMY_part

The ORIGINAL parts included here are 'cleaned' versions of the original stls (cleaned with varying success :-) ):

-) ASA_handlebarclamp_ORIGINAL_cleaned

-) ASA_midsection_ORIGINAL_cleaned

-) ASA_screwholder_ORIGINAL_'cleaned'_2x

-) TPU_holder_ORIGINAL_cleaned_2x

-) TPU_midsection_ORIGINAL_cleaned

The bill of materials is similar to the original:

• 1x M6x60mm hex bolt

• 1x M6x30mm hex bolt

• 2x M6x30mm Allen key bolt with cylindrical head

• 3x M6 nut

• 1x M6 Nyloc nut

• 1x M6 long nut (20mm)

• 1x M3x40 bolt with countersunk head

• 1x M3 Nyloc nut

• 4x 2.2x10mm screws

• 2x 6mm magnesium/aluminium/steel rod, 70-80mm long

Printing: The PETG parts were printed with 100% infill, the PETG-CF with 50% and 100% (ASA_topsection) . The TPU parts were done with 25% (TPU_holders) and 100% (TPU_midsection). All parts feature 3 perimeters. 

I have done my build without using ASA, which I honestly don't like to print. Instead PETG (ASA_handlebarclamp and ASA_midsection) or PETG-CF (ASA_mainsection, ASA_topsection, ASA_screwholders) and TPU (TPU_holder and TPU_midsection) was used. For the rods I use 2*6mm*100mm AZ31 magnesium alloy rods to reduce body forces of the damped parts. If you can believe that, they are available on ebay :-). I put a drop of oil in the long nut and the two holes for the magnesium rods (after all they could corrode in the long term). The Mg rods were ground at the ends and deburred before glueing them into the ASA_topsection. 

The assembly is exactly like the original, so I won't repeat that here. 

I will report back on the usage of this on my MT-07 (naked bike). The phone will be directly in the free air stream, so this could be interesting, we'll see how this turns out.

Safe rides,

emefff.

UPDATE: On my MT-07 fitting the holder is only possible on the clutch side. I even had to loosen the clutch assembly a bit to fiddle the handlebarclamp in there. The last image shows it mounted on the bike.

UPDATE II: In the meantime I have used the clamp numerous times, without any problem.