1 / 4
HDD Expansion Cage for a Fractal Focus 2 Case — image 1
1 / 4

HDD Expansion Cage for a Fractal Focus 2 Case

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Install up to 9x 3.5" HDDs to a Fractal Focus 2 case.

Rating
0 / 5
Likes
1
Downloads
14
Makes
0
Views
363
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution

The Fractal Focus 2 case doesn't offer much in terms of 3.5" HDD mounting. I wanted to use that case for a server with a large RAID array. This project is the solution I came up with.

BOM:
  • (28) M3 heatset inserts

  • (28) M3-8mm SHCS

  • (2-4) printed cage brackets

    • (2) if mounting 3-5 drives

    • (4) if mounting 6-9 drives

  • (4-8) printed washers

    • (4) if mounting 3-5 drives

    • (8) if mounting 6-9 drives

  • (2-4) printed cage adapters

    • adapters 1 & 2 if mounting 3-5 drives

    • all adapters if mounting 6-9 drives

  • (x) Phanteks Stackable 3.5" HDD Brackets

    • based on the number of drives to be mounted

  • (4) printed bottom bracket standoffs

  • (2) printed bottom bracket mounted standoffs

  • (1) printed bottom bracket

Instructions:
  1. Add heatset inserts to printed parts. Note: the bottom bracket mounted standoffs have heatset inserts on both sides of the standoffs.

  2. Mount drives in the Phanteks cages using the provided hardware. Reference photos to confirm final drive orientation.

  3. Clip the Phanteks cages together to create the stack.

  4. Attach the cage adapters to the cage brackets using M3 bolts. Don't attach anything to the Phanteks cages yet. Orientation marks on the prints indicate up and towards the front of the case. The odd-numbered adapters (wider) go towards the front of the case. The even-numbered adapters (narrower) go towards the rear of the case. Adapters 1 & 2 are attached to a set of printed cage brackets. Adapters 3 & 4 are attached to another set of printed cage brackets. The embossed numbers and orientation marks go on the inside and aren't visible once attached.

  5. There is a notch on one end of the printed cage bracket that engages the metal edge of the Phanteks cage. Slip them over cages 1 and 3 in the stack, and then line up the diagonal bump on the other with the metal cutout of the Phanteks cage. Secure the printed cage brackets to the Phanteks cage from the INSIDE of the cage. Repeat for drive cages 6 & 8 if using.

  6. Attach the bottom bracket standoffs to the bottom bracket. The 4x standoffs (slightly longer) are mounted to the four corners. The 2x standoffs (slightly shorter and with heatset inserts on both ends) are for the middle locations.

  7. Attach the bottom bracket to the case, leaving the bolts loose so that the bottom bracket can be adjusted.

  8. Carefully place the drive stack into the case on the bottom bracket. The printed cage brackets and adapters will be facing the motherboard side of the case. Adjust the drive stack forward/backward until the heatset inserts are visible through the stock mounting holes on the backside of the case.

  9. Using the printed washers, attach the cage adapters through the backside of the case using M3 bolts.

  10. Tighten the two bolts on the underside of the bottom bracket once everything is adjusted. They only need to be tight enough to prevent any side-to-side movement.

Notes:

I was able to just barely fit a 9th drive in the stack with a CPU radiator installed. YMMV.