1 / 8
Wet-Sanding Handle for #8 Meat Grinder Blade and Knife — image 1
1 / 8

Wet-Sanding Handle for #8 Meat Grinder Blade and Knife

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A handle designed to hold a #8 meat grinder plate and knife flat with even pressure while sharpening.

Rating
0 / 5
Likes
2
Downloads
5
Makes
0
Views
41
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

If you use a #8 meat grinder, you need to regularly sharpen the plates and knife for optimal grinding. An inexpensive way to do this is with wet-dry sandpaper (instructions for that at the end of the description).

Doing this with just your hand is a bit tiring because you need to focus on consistent even pressure, and as you sharpen the cutting surfaces start to get a bit nippy.

This handle is designed to hold grinder plates flat and steady while wet-sanding. An adapter is included that should fit most grinder knives, but no guarantees, I only have one make of grinder.

Recommended print settings:

Material: Definitely use PETG, sharpening action generates heat and friction. Softer materials break down quickly.

Walls: Again, this handle needs to be pretty strong, so I'd go with 4-5 loops.

I recommend 20% gyroid infill.

Supports: Depends on print orientation, but I'd go with the handle facing down on the plate and using slim tree supports.

How to Wet Sharpen Grinder Plates and Knife

You'll need:

  • This 3D design printed (the handle and knife adapter), to hold the pressure evenly across the grinder component. Also to protect your fingers during sharpening.

  • An extremely even flat surface; a sheet of glass, piece of marble, or very flat piece of metal. Tabletops or other surfaces may have small deformities that will make the sharpening ineffective.

  • Wet/dry sandpaper; silicon carbide paper in grits 320, 600, and 1200.

  • Lubricant, either honing oil or water with a drop of dishwashing detergent.

  • Permanent marker for showing where sanding has been done.

Process:

1. Prepare the Surface

Clean the plate and knife thoroughly to remove any dried fats or proteins. Secure your sandpaper to the reference flat. You can do this by wetting the back of the paper so it suctions onto the glass, or by using a light spray adhesive. Avoid double sided tape, it ruins the flatness of the sharpening surface.

2. Mark the Plate

Take your permanent marker and colour the entire cutting face of the grinder plate and the polished cutting surface of the knife. As you sand, the marker will disappear from the high spots first. Once the marker is completely gone, you know the surface is uniform

3. Sharpening the Plate

Apply your lubricant to the 320-grit paper.

Insert the plate into the underside of the 3d-printed handle, making sure the notch in the plate aligns with the notch on the underside of the handle. Using firm, even pressure, move the plate in a figure-8 pattern over the sandpaper.

Rotate the plate 90 degrees every 10–15 strokes to ensure even wear (the handle has a projection on the upper surface so you can keep track of orientation).

Once the marker is gone and the surface looks consistent, take the blade out, colour the other side with a marker, and reinsert with the unsharpened, coloured face downward. Repeat the actions above.

Repeat with the 600 grit and finish with the 1200 grit.

4. Sharpening the Knife

Insert the knife adapter into the underside of the handle. Insert the blade into the adapter (it'll be loose because each brand of grinder has different knife shapes and the design of the adapter tries to fit most).

Repeat the same figure-8 motion as above using the three grades of sandpaper with the knife. The knife blade only needs the flat cutting surface sharpened, so no need to flip it.

Try to keep the knife perfectly flush against the paper at all times.

5. Deburring:

After sanding, there may be very small burrs of metal at edges of the holes and knife blade. To remove them, use the handle to run each side of the plate over a sheet of cardboard several times in a figure eight, rotating 90 degrees every few passes.

6. Grinder Component Storage:

Carefully wash and dry the parts and then coat lightly with a food grade mineral oil before storage to prevent rust.

Tags