Otto RUN! — The Alarm Clock That Escapes When You Snooze!
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
An alarm clock that physically runs away when it is snoozed. You have to get up and find it to turn it off!
- Rating
- 0 / 5
- Likes
- 13
- Downloads
- 21
- Makes
- 0
- Views
- 246
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- RC & Robotics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Otto RUN! — The Alarm Clock That Escapes When You Snooze
⚠ Design concept. All parts have been modeled, fit-tested in CAD and 3D printed, but not yet fully assembled and tested with real Otto hardware. Build feedback is welcome. ⚠
Otto RUN! is a remix of the HP Robots Otto Starter into a fully functional alarm clock with one rule: if you snooze, Otto rolls off the nightstand and runs away. You have to find and catch him and hold your hand in front of his sensor for 3 seconds to turn the alarm off.
Set your alarm from any phone or laptop browser. Otto handles the rest.
How It Works
Otto sits on your nightstand and shows the current time on his LED face. When the alarm goes off, hold the button for 1.5 seconds to turn the alarm off without snoozeing or press the button once to snooze — Otto plays a short sound, then rolls away and starts moving. He avoids walls, changes direction randomly, and keeps alarming while he moves. Find him, hold your hand in front of his face for 3 seconds, and he disarms with a happy animation.
What You Need
From the HP Robots Otto Starter Kit:
Motherboard (ESP32)
2× wheel servo motors
Battery
8×8 LED matrix
Ultrasonic distance sensor
Push button
Screws from the set:
4× M2×7 — battery cover
4× M2×7 — servo plate to body top
2× M2×4 — servo holder to plate
4× M2×4 — button board
Extra hardware:
4× 608 skateboard bearings
No soldering required. Everything uses the original kit connectors.
Printed Parts
Part | Material | Notes |
|---|---|---|
Body top | PETG | — |
Body bottom | PETG | — |
Body center | PETG | — |
Servo and button base | PETG | Mounts to top body part |
Servo holder | PETG | Screws to base |
Wheel base ×2 | PETG | Main structural wheel part |
Axle (peg) ×2 | PETG | Press fit — see print tips |
Wheel tire ×2 | TPU | Flexible outer ring |
Button cap | PETG | Printed cap |
Original Otto parts reused: battery cover, face mask with LED matrix.
Print Settings
All parts print at 0.2mm layer height, 0.4mm nozzle. No supports needed for any part.
Axle (peg): Print horizontally with 5 perimeters and gyroid infill.
Wheel base: PETG only. PLA might crack on hard floor impacts.
Wheel tire: TPU at 95% infill. Use 0.3mm layer height — TPU flows more cleanly at slightly thicker layers.
Everything else: PETG, 3 perimeters, 15% infill.
Assembly
1. Print all parts. Test the axle press fit on your servo horn and wheel base before printing the full set. A correct press fit needs firm hand pressure but no tools.
2. Install bearings into body. Press two 608 bearings into the bearing pockets in the body. They should seat flush with firm thumb pressure.

3. Assembly servos and button. To the top body part, add button cap. On the servo holder, secure the button board with 4× M2×4 screws.. Attach the base to the body top with 4× M2×7. Secure the servo holder with 2× M2×4.

4. Insert axle into the wheels. They should seat flush with firm thumb pressure. The profile prevents rotation — it should feel locked with no wobble. Snap the TPU tire onto the wheel base rim.
5. Connect the wheels with the servos. Push the axel through both ball bearings full way in. The axle should be connected with the servo output horn now.

6. Install board with battery. Place the board with battery in the center body part as it is in original Otto design. Connect the board with sensors and servos.
7. Connect electronics. Plug the LED matrix, ultrasonic sensor, servos, press button and battery into the motherboard using the original kit connectors.
8. Assemble body. Clip the body top and bottom together.

11. Flash firmware. Download the MicroPython firmware from GitHub (link below). Flash to the ESP32 using Thonny IDE — full instructions in the repository README.
12. First boot. Otto creates a WiFi network called OttoSetup. Connect from your phone, enter your home WiFi password, done. Visit otto.local in any browser to set your alarm.


Firmware
Otto RUN! runs on MicroPython. On first boot it opens a WiFi setup portal — no code editing needed. Alarm time, snooze duration, and on/off are set from a simple webpage at otto.local from any device on your network. Time syncs automatically via NTP.
The alarm runs a five-state sequence: clock display → alarm → snooze → runaway → disarmed. While moving, Otto uses the ultrasonic sensor to avoid obstacles and changes direction randomly so his path is different every morning.
Full source code with readme is attached.
Expansion Ideas
Sunrise light mode — add an SK6812 RGBW LED strip inside a printed diffuser dome for a gentle wake-up light before the alarm triggers. One GPIO pin, no extra libraries.
Multiple alarms — weekday and weekend profiles via the web UI.