1 / 13
Mount to allow PiKVM DIY to use PiKVM Metal Case — image 1
1 / 13

Mount to allow PiKVM DIY to use PiKVM Metal Case

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Allows you to build the PiKVM DIY V2 using the metal case from the PiHut and use the 8086 USB-C splitter and 0.91 OLED

Rating
0 / 5
Likes
0
Downloads
2
Makes
0
Views
54
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — Noncommercial

I really like the PiKVM metal case, and for £30 UK from the Pi Hut it is pretty good value.  With the case, you get a good 0.91 OLED mount, display and 5v fan -  expecting you to buy the companion PiKVM hat.

I had the Waveshare HDMI to CSI Adapter for Raspberry Pi , and an 8G PI4 so I designed this plate to mount the remaining components inside this case.

I printed the plate in Polymaker Polylite grey ASA using the standard Voron parts profile.

Parts - Electronics and Cables

Hardware

  • Build Plate STL - Add 4 m2.5x3.5x4 threaded inserts 

  • PiKVM Metal Case

  • 4 x M2.5 x 3mm Threaded Standoff F-F or (M2.5 Countersunk 10mm screw + nut and plastic washer) See image

  • 4 x M2.5 x 16mm Threaded Standoff F-F

  • 2 x M2.5 x 10mm Threaded Standoff M-F

  • 2 x M2.5 x 15mm Threaded Standoff M-F + 1mm Plastic Washer to finely adjust washer

  • 2 x M2.5 x 12mm countersunk screw - used to fit through OLED mount

  • 2 x M2.5 x 8mm countersunk screw

  • 4 x M2.5 x 12mm countersunk screw and nuts to hold the fan

  • 3 x M2.5 x 6mm button head screw to hold HDMI to CSI module

  • 1 x M2.5 x 8mm button head screw to secure USB splitter 

Instructions

  1. Feed m2.5 x 10mm screw and screw-down standoff or nut&washer combination

  2. Fit the PI - angle in the usb/ethernet end

  3. Screw on the 16mm Female - Female standoff and fit the HDMI and short usb cables

  4. I removed the barrel jack socket from the splitter board and chamfered the corner so it doesn't hit the standoff

  5. Attach the cables to both the HDMI adapter and splitter  and screw to the mounting plate using the cap head screws

  6. Secure the mounting plate using 15mm M-F standoffs at the HDMI end and 10mm M-F standoffs at the USB/ethernet end. Depending on the 10mm standoff you may need to add a washer to ensure the OLED mount fits correctly over the standoff so that it fit correctly into the lid.

  7. To provide the maximum clearance - solder the wires to the underside of the OLED display and crimp Dupont connectors into a 1x5 way socket.

    PI4 Pin

    NAME

    OLED

    01

    3.3v

    Vcc

    03

    SDA - i2c

    SDA

    05

    SCL - i2c

    SCL

    07

    NOT

    USED

    09

    GND

  8. Depending on your supplier, you may need to extend the wires and crimp a 1x3 Dupont connector onto the 3010 5v fan. You can add a PWM fan if required, but my PiKVM is not used 24x7, so I am going with a simple always-on 5V fan for cooling.

    PI4 Pin

    NAME

    FAN

    02

    5v

    5v

    04

    5v

    Not

    Used

    06

    GND

    GND

  9. Slide the display into the mount and install it on top of the 10mm standoffs.

  10. Fit the fan to the side of the case using the 4 x 12mm

  11. Fit the lid using 12mm countersunk screws into the case lid through the display mount into the standoff

  12. Add the 8mm countersunk screws into the case at the HDMI end.

  13. Follow the PiKVM DIY build guide to configure the software.

Tags