Mamiya RB67 Pro-S Instant Film Back (using JollyLook square dev unit)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Custom film back for the RB67 which allows for shooting Instax square film. Requires the JollyLook SQUARE dev unit.
- Rating
- 0 / 5
- Likes
- 17
- Downloads
- 81
- Makes
- 0
- Views
- 838
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Photo & Video
- License
- Creative Commons — Attribution — Noncommercial
THIS MODEL REQUIRES THE JOLLYLOOK SQUARE DEV UNIT TO WORK
This custom back allows for shooting Instax square film on the Mamiya RB67 (Pro-S tested only). The included dark slide allows the back to be changed out mid-cartridge.
Note: I included a model called "alt mount test print" that can used to fit-test the mounting surface that the back uses. If you have a model other than a Pro-S (or you just want to make sure things will fit before committing to printing/buying everything), I suggest printing this model (along with the mounting studs) and checking the fitment on your camera.
Why print this?
Modified Instax bodies turned into custom backs cost ~$500 and they require batteries (gross!)
The JollyLook custom back costs $170 and (afaik) isn't even shipping yet.
This model is (relatively) cheap to assemble, uses no batteries, is ready to use as soon as you're ready to make it, and is fun to assemble :)
Total cost (in USD) is ~$82 (pre-tax) with $55 of that coming from the cost of the dev unit and the rest coming from the assorted assembly materials (+ the cost of the whatever filament you use).
Printing and Assembling
The following sections will give only details necessary to print/assemble/use this model, the next section has tips/quirks/notes/etc.
Requirements
Strict:
JollyLook Square development unit: https://jollylook.com/products/jollylook-instax-square-film-development-unit
Everything is built off of using this for actually developing the Instax film, so yeah it's required.
(I tried a completely 3d-printed approach for development but I couldn't get the rollers to squeeze the developer pouch properly so here we are)
Some form of black felt for light-proofing seams:
I used this https://a.co/d/0goJEd7W (5PCS Self Adhesive Felt Sheet - Black Felt Sheets with Adhesive Backing for Drawer/Jewelry Box Liner (9" x 11"))
It's about 1mm thick. Thicker is probably also okay
If you use something else make sure it's self adhesive
M3 bolts of assorted length
https://a.co/d/0591SCE7 (380 Pcs M3 Black Flat Head Machine Screws and Hex Nuts Kit Carbon Steel Countersunk Head Phillips Screws Bolts Assortment,M3 x 4mm/ 6mm/ 8mm/ 10mm/ 12mm/ 16mm/ 20mm)
Models are design for use with heat-set inserts but might be modifiable to thread straight into the print
Attempt at your own risk
Strongly recommended:
*OEM Mamiya rotating back mounting studs

The little grey studs that allow the rotation assembly to connect to the main camera body
Mounting these to the models requires M2.5 heat-set inserts
The original (tested) mounting face in this model uses these, but I included an alternate version which can use printed studs
Heat-set inserts
https://a.co/d/04uQFVmB (400Pcs Threaded Inserts, M2 M2.5 M3 M4 M5 M6 Female Thread Metric Knurled Nuts Assortment Kit, Brass Heat Set Insert for Plastic and 3D Printing Components (Threaded Inserts Ket)
Adds a lot of fastening strength
Also ensures that everything fits snugly so flange focal distance is correct
Electrical tape (or similar dark adhesive strip)
Helps seal the dark slide slot
Printing
A lot of the print settings (perimeters/layers/infill/etc.) were just what I had set at the time. These can probably be tweaked if you know what you're doing.
Material:
PLA and ASA explicitly tested
Perimeters: 3
Layers:
Top: 5
Bottom: 4
Infill: 25%
Layer Height: 0.2mm
Supports:
Required?: Yes, for everything
Brim: Recommended to keep everything flat (especially when printing in PLA)
Plate Adhesive:
Would recommend using some stick glue to keep large flat pieces from warping
Orientation:
Everything is oriented correctly in the files
You can experiment with other orientations but these orientations are optimized for keeping keeping flat surfaces as flat as possible
Print one copy of everything the Main Components section* except for the latch components (print two of those each)
*Only if you're using the OEM mounting studs. If not print the alternate body - mount file in Alt Mounting Face.
This requires 1 large mounting stud and 3 small mounting studs.
Large stud goes here:

Assembly
Generally, you should be able to assemble in same order as the assembly steps below.
An overview of the assembly process is something like this:
Slide the dev unit into "body - main"
Add heat-set inserts/add light-proofing
Fasten everything together
Add hinges
Attach roller crank knob
Heat Set Inserts
I don't remember the height of a lot of these insert and I don't want to dig around and find out. Look at the model and use common sense. A lot of the holes are oversized so there should be plenty of wiggle room for different sizes based on whatever you have.

The 4 locations above use M2.5 inserts. These are only required if you're using the OEM mounting studs. Place in the holes in "body - mount".

These 4 inserts are M3 and go into "body - main".

The above 2 inserts are M3 and go into the "body - back" model. There's not as much wiggle room with this one so try and use a short insert.

These 2 inserts are M3 and go into "body - main".

There are 4 total inserts required for the latch bases, all are M3. They should be placed in the holes on each side of "body - main"
Light-proofing
This is a mix of definitely required and only sort of required felt locations. I definitely used more than was necessary, but I don't have any light leaks. Feel free to play around with these as you see fit. You can use a flashlight to shine into seams to see if felt would help.

Thin strips of felt on the sides and top of the dev unit. These aren't strictly necessary but I found that they help how light-resistant the dark slide is (see the notes section at the bottom).

If you look closely, there are two levels of felt here, I circled the parts I think are necessary. Part of the felt is on the lip of the "main - body" part and the rest is on the dev unit itself. The lip portion is necessary, but I don't think the felt of the dev unit does much, your choice whether to add it or not. At the very least, add felt to the top of the dev unit to seal against the back.

This is below the mounting face. I don't think these are necessary, but it's easy to add and ensures there's no light leaking.

This is the bottom where the dark slide is inserted. Use two thin strips on each side. I found that tweezers helped a lot with placing these.

On the back side of the mounting face you'll want to add felt in the yellow area. Additionally, in the blue area, you'll want to add some back electrical tape (or similar adhesive-backed, dark material). The idea with the tape is to fold it over on itself (lengthwise) and leave a small portion with adhesive exposed. You should place the tape such that the folded section is against the yellow portion, acting as a sort of flap above the dark slide slit that moves aside when inserting the dark slide and presses against the felt when the dark slide is removed. I found this helped a lot with reducing stray light from the bottom.

The felt goes between "body - top" and "body - main" here. Just a thin strip around the perimeter is good enough. I'd highly recommend adding some type of flap (similar to the electrical tape one above) above the top slot. The dev unit has some felt above the rollers but it tends to shift. This flap helps keep a lot of stray overhead light out.
Fasteners
At this point you should be able to start screwing bolts into the inserts you added. All the heads are countersunk you optimally you'd want to use countersunk head bolts for flush fitment. The required sizes are varied so use whatever you think works best.
Hinges
This design uses standard 1.75mm filament for all the hinges. Just cut a piece of the appropriate length and push it through the preexisting holes. There will probably be support material that you'll need to remove with tweezers. Also, if printing in PLA, you might find that the holes shrink a little too much for the 1.75mm filament. If that happens, your best bet it just drilling it out with a small bit (Harbor Freight has a decent micro drill bit set for a few bucks that's helpful for lots of things, including this).
The fit is tight enough that the hinge material shouldn't slide out, but a nice trick is to cut a length slightly longer than you need, then heat a piece of metal and press it against the end of the filament to flatten it out and effectively lock it in place.
In total, you need filament for 3 hinges pictured here:


Crank Knob
Pretty straightforward, just attach the small geared + keyed piece included in the dev unit kit in the crank hole. Make sure it engages all the way in (it has a tendency to get stuck halfway in because the gear teeth are blocking it). If it's not fully engaged, try rotating the piece while applying force until it slides in fully. Once done, match up the keyed hole on the crank knob to the nub on the small geared piece you just inserted. Press firmly to get it to seat all the way down.
The dev unit kit should include two flat-ended bolts, one shorter and one longer. Insert the longer bolt into the hole in the crank knob and drive it until the bolt is fully seated. The knob should have no play and should be sitting 1-2mm away from the model body.
Using the back

Slot the Instax square cartridge into the back as shown (make sure to press it all the way down). Position the two pieces of foam (included in the dev kit) in the two circled slots and close the back. Try and make sure the felt doesn't shift around, the felt is important for keeping pressure on the frames so they're flat and they lift into the rollers correctly.

With the back closed, insert the latch arms into the latch hooks so the back stays closed. The dark slide isn't necessary yet since the cartridge has a dark slide of its own. However, if you're not attaching the back immediately, insert the dark slide anyways for extra protection.
Release the rotating back arm at the bottom of the RB67 (and remove the existing back if one is attached), then line up the mounting studs with the openings on the camera. The waist-level viewfinder will need to be extended for the back to fit properly (see notes below). Once the back is fully seated, close down the rotating back arm on the camera.
Remove the dark slide when you're ready to shoot and remove turn the roller crank knob until the Instax cartridge dark slide comes out the top. Don't pull it out, just turn until it pops out and then gently pull it out the top.
At this point you're ready to shoot. Wind the mirror/shutter lever on the camera, release the shutter, then crank the knob until the frame comes out. Give the frame ~90s for an image to appear and ~5-10m for development to finish.
When you want to remove the back, re-insert the dark slide (all the way), then release the rotating back latch and remove the back. Place in a dark area promptly and avoid pointing the front directly at light sources.
Notes/Quirks/Etc.
A few important things to note regarding the design/use of this back. You can decide if any of these are deal breakers for using this model.
The dark slide isn't 100% effective
Maybe this is obvious but if you were to point the front of the back (when removed) at a bright light source, odds are you'll see some light streaks on the next frame. This is mostly because of the two holes near the top of the mounting surface which make room for two metal arms extending from the back of the camera.
The thin strips of felt on the front of the dev unit help minimize this issue (as in you won't see any issues if you remove the back in the shade and promptly place it somewhere dark), but they won't make it light-proof.
The viewfinder can't seat fully when the back is attached
There's a slight clearance issue with the mounting plate and the edge of the waist-level viewfinder.
There might be a design fix for this, but I couldn't think of one
This design is also completely untested with a prism viewfinder
The frame area is slightly left shifted to accommodate the dev unit gearing
It's very slight (~a couple mm) but it's there. Image framing is almost exactly the same, but it's worth testing/keeping in mind if you care a lot about exact framing.
Flange focal distance isn't perfect
I did a lot of testing to make sure it's as good as can possibly be (within reason), but it'll never be perfect.
Hard to quantify the error, but you can expect ~1mm off when shooting wide open at minimum focusing distance (as tested on the 127mm/f3.8).
You may be able to adjust this away using more (or maybe even less) felt between "body - main" and "body - mount". You'll probably want to use a frame or two to test at first.
I've noticed some issues with feeding frames into the roller towards the end of a cartridge
It may require a few extra crank cycles to get frames to exit correctly, especially in the last few frames of a cartridge.
This may be fixable with thicker foam and/or a small lip which increases the foam compression when closing the back
The dark slide can be a bit difficult to remove when the back is attached
This is not a huge deal, but something to be aware of
The dark slide is oversized (length-wise), so the best approach is to retract the dark slide a few mm before attaching so there's a nice surface to grip once fully attached.
Inserting the dark slide can be difficult as well. Make sure it's going in fully straight.
Overall, everything functions correctly, I just wanted to make sure all the quirks are fully disclosed so you can decide for yourself what is/isn't acceptable.
If you have any comments/concerns/suggestions please let me know. I'm always open to making improvements if any are suggested.