Volvo V50 S40 C30 C70 Carplay mount - Updated
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A mount for a cheap Carplay screen that replaces the standard radio face plate fascia. - Updated
- Rating
- 0 / 5
- Likes
- 8
- Downloads
- 65
- Makes
- 0
- Views
- 915
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Share Alike
Volvo V50 / S40 / C30 / C70 CarPlay Fascia Mount Remix
Remix of the DS Prints Custom Volvo V50 / S40 / C30 / C70 phone mount design, modified to remove the phone mounting section and replace it with an angled mount for a low-cost CarPlay display.
Please check out the original design - it’s an excellent piece of work, clearly explained throughout the description, and fits perfectly as a replacement for the original fascia.
UPDATE - I have redesigned this model to use 3x M4 threaded heat inserts and 3x M4 Screws/Bolts. This should allow for a safer, more secure fit. I have also included a Pilot Hole Guide for proper alignment.
For most people, the original design will likely be the easier and cleaner solution for mounting a phone for navigation or media. However, if you want a dedicated CarPlay screen and/or rear-view camera setup, there are very few good mounting options without sticking a display awkwardly to the dashboard and potentially obstructing your view of the road. This remix was designed to solve that problem.
This design is intended for use with one of the many inexpensive standalone CarPlay displays available online. I used a unit purchased from AliExpress which cost approximately £30.

WARNING
This design is somewhat awkward to assemble and is not optimised. There is a risk of damaging the CarPlay device if care is not taken during installation or use. Proceed entirely at your own risk.
I accept no responsibility or liability for any loss, damage, injury, or other consequences resulting from following these instructions.
There are many different variations of CarPlay devices available online. The unit I used is similar to the one shown in the photo above. Other similar models should work, but compatibility cannot be guaranteed.
Additional note: my head gasket has since blown, so I currently have no plans to further optimise or redesign this mount. The design worked well enough for my use case during the 6 months I owned the car, but there is definitely room for improvement if someone wants to refine it further.
The Design
Although the design appears simple, considerable time went into adjusting the mounting angle to achieve the best compromise between driver visibility, screen fitment, and dashboard clearance.
In my Volvo S40 (right-hand drive), the ignition barrel is positioned to the left of the steering wheel, which made placement of the screen particularly awkward. This design still leaves sufficient clearance for the ignition key while maintaining full visibility of:
The original radio display
All factory buttons
Hazard light controls
Printing
Recommended material: PETG or other heat-resistant filament
PLA is not recommended as it may deform or melt in a hot vehicle interior
Recommended infill: 15% minimum
I would recommend printing the part on its side for best fitment. Printing it flat on the top edge did not produce as accurate a fit in my testing, although this may have been due to poor filament quality at the time.

Mounting Instructions
To mount the CarPlay device, I used 3x 3mm diameter wood screws that I had laying around. I have since updated the design, now requiring 3x M4 threaded inserts, as the wood screws added unnecessary risk when working with the CarPlay device. This should allow for a safer, more secure fit.
Step-by-step
Remove the rear panel from the CarPlay device.
Use the printed Pilot Hole Guide to mark pilot hole positions on the back casing of the CarPlay device (where the original stand normally mounts). This will ensure proper alignment.
Drill pilot holes carefully with the rear casing removed to avoid damaging internal components. If possible, drill from the inside outward. 4mm Drill bit recommended.
Attach the mount using the M4 Screws/Bolts.
This can be assembled either direction, but I recommend positioning the screw/bolt heads inside the CarPlay housing to reduce the chance of damaging the CarPlay device
Reassemble the CarPlay device.
Carefully remove the original radio fascia from the vehicle:
Two clips are located at the top
The fascia then pivots outward
Replace the original fascia with the new printed assembly.