Sony Walkman WM-10/WM-20/WM-30 Take-up Reel or Supply Reel Gear
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A replacement take-up reel or supply reel gear for the Sony Walkman WM-10/WM-20/WM-30 or WM-F10/WM-F20 cassette player
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 48
- Makes
- 0
- Views
- 211
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Audio
- License
- Creative Commons — Attribution — Noncommercial
This is a replacement gear that fits over either the take-up reel or supply reel for a Sony Walkman WM-10/WM-20/WM-30 or WM-F10/WM-F20 vintage portable cassette player from the 1980s. As originally manufactured, they were made out of a plastic that shrinks when it gets hot (like when it's left in a hot car) and also becomes brittle with age. Many of these Walkman cassette players today have one or both of these gears with a crack in it that has opened up, making playback either rough or impossible.
This design is from a couple years ago, when nobody was manufacturing replacement gears and they could not be purchased anywhere. This is the result of two months of work and 34 different design revisions. There are 118 teeth on these fairly small gears which results in a gear tooth pitch of about 0.96mm, which is challenging to resolve cleanly for even the smallest practical printer nozzle size of 0.25mm. Small defects end up being large compared to the gear tooth size.
Through trial-and-error, this design exaggerates the gear tooth profile and builds in some dimensional errors to counteract the printing limitations at this scale, so that the final result has the desired shape. A few inconsequential dimensions of the gear were changed for strength and printability.
Some micro-notches were also built into the design that do not resolve in the final print, for the purpose of controlling the extrusion path to maximize strength and reduce surface defects. Without these notches, the slicer will insist on drawing each gear tooth as a separate disconnected loop and it will connect them with separate little stubs of filament. We only have room for a single extrusion line around the gear teeth, and starting/stopping the extrusion is disastrous. It will break while being installed.
Printing
This is an incredibly-difficult model to print. It will almost certainly not work for you. It was heavily tuned for my particular printer (Prusa MK3S+), nozzle, filament, and slicer. You must use PrusaSlicer to slice the model, and you must print it in Prusament PETG Jet Black with a 0.25mm nozzle and the 0.10mm DETAIL profile. Anything else will mess with the dimensions in places and the gear won't work correctly. A more modern printer might be more accurate, but that might not be a good thing because this model has purposeful defects built into it to work with this specific printer's shortcomings. This print is right at the edge of what's possible for FDM printing. You have been warned.
These are the PrusaSlicer-2.9.x setting changes from default that must be used to get proper extrusion behavior and dimensions:
Seam position: Random
Speed for perimeters: 20mm/s
Infill/perimeters overlap: 10%
Slice gap closing radius: 0mm
Elephant foot compensation: 0.1mm
Perimeter transitioning threshold angle: 30°
Minimum feature size: 0%
It will not work without any of these settings. Even with these settings you will only have about a 50% success rate with the print, where failure means that the gear does not run smoothly when installed and it will get tight in spots. The resulting gear tooth shape is not ideal, but it can work when printed well. If printing more than one gear at a time, you must use sequential printing to avoid nozzle movements that add blemishes to the surface.
SLA printing is absolutely the way to go with a part this small and with such fine details, although this model is distorted enough to be completely inappropriate for that purpose.