LowRider v4 CNC - Kinematic Mount for Crosshair Laser
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Mounts a crosshair laser to the Lowrider 4 using kinematic the mounting components by @Design8Studio and @Jamie
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 7
- Makes
- 0
- Views
- 77
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Tools
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
I basically used a device mount from @Design8Studio as a starting point and did a remix to accommodate an inexpensive crosshair laser module, and a boost/buck converter. Lots of these efforts use a battery pack but I will forget to turn them off and burn through batteries, so this seems a better approach for me.
Note that there are multiple things called a "mount" in this topic. To actually attach something requires 4 pieces, in two assemblies. The first assembly attached to the core is composed of 2 parts: a "main mount" that attaches to the LR4 core router/spindle holders, and an attached magnetic "fixed mount". The second assembly is a "mobile mount" and an attached to a specific "tool mount" (pen holder, frag knife holder, etc.). The second assembly is held to the first by the magnet. What is here is the fourth part, a tool mount.
The laser mount has three sections - a cylinder to hold the laser module, a small box to hold the boost/buck converter, and a circular attachment point for the mobile mount component. The laser module is a snug fit into the cylinder and the boost/buck fits nicely into the box. A slide on lid for the box part is also included.
I also made a small bracket to mount a coaxial power jack onto the XMax side of the core, using the slot that was (I think) originally intended for a high side limit switch. The bracket can go on the other side if needed. Just mirror it in the slicer. The bracket has space for a second jack, which I use to plug in the touch plate. Both holes are 8mm.
The bracket may result in a small loss of usable X capacity, but so will the kinematic mount itself, so the net effect of the bracket may be small.
Related parts:
The original kinematic mount by Design8Studio is here.
The updated parts for the Lowrider 4 are here.
The updated designs by Jamie are here.
For a Lowrider 4, go to #2 and get the "main mount". Then from #3 use the "Part B, Fixed Base with Mountains" (see note in "Printing" below) and the "Part C, Mobile Base with Valleys".
Assembly notes:
Solder some input wires to the converter, then connect it to the power supply (I use 24V from the controller) and use a voltmeter to adjust the output to 3.3V. Disconnect from power. Slip the laser into the cylinder, running the wire leads into the box. It should be a snug fit. If it's a bit loose, a short 2.5mm screw into the side hole will hold it in place. Don't over tighten the screw. and attach the laser leads to the converter output. Slip the converter power leads through the box from the inside to the out, and then put the board into the box. Secure with 2 short 2.5mm screws if desired. Slide on the lid - it may be stiff but should get looser after a few cycles. Attach this to the "Part C mobile base" kinematic mount half with 3 M3x16 screws and nuts.
If you are using the power bracket, solder a mating coaxial plug for the jack you used - the center conductor is the positive. Wire the jack to power - again, center pin positive. I powered this by using 24V from the controller. If your extra crafty, use a 24V GPIO from the Jackpot controller and switch this on/off with a Jackpot macro command. But remember to switch the low side. The laser doesn't draw much current - about 3mA - but low side switching is recommended on the Jackpot.
Parts used:
6 M3x16 screws and nuts
2 M5x45 screws
Fender washer, 1.25"
Printing:
Print as oriented. PLA or PLA+, 30% infill, 0.3mm layer height. I suggest supports to hold the top of the laser cylinder up and keep it more round, but you can try without and see what happens. I used clear PLA for the lid so the LED on the converter will create a bit of a glow,
When printing the "Part B, Fixed Base with Mountains" I found the recess for the magnet was not deep enough. I had to increase the cavity depth 2.5mm for the magnets I used.