1 / 4
2U 10" rack enclosure for 720q 920q 920x p330 — image 1
1 / 4

2U 10" rack enclosure for 720q 920q 920x p330

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

2U 10" rack enclosure for 720q 920q 920x p330 to use Dual PCIe cards or dual slot PCIe single card.

Rating
0 / 5
Likes
6
Downloads
13
Makes
0
Views
477
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

I love the lenovos 720q 920q 920x  small computers because they have a riser card that is capable of having a 8XPCIE card. However, one thing I learned when diving into this platform, was that on the riser connector, there our two different PCI lanes connected to that. It may have seen that Lenovo does have some options on where these risers normally connect to. After looking into the schematics that I saw online of this computer, and seeing other people being able to make their own risers, I decided to try and tackle that on my own. My professional work is designing PCB boards for the automotive world. But I did also have experience in the past running high speed data lines. However, I don't use kicad, and my Altium software are expired from my previous job. So I gave it a shot and i built it using EasyEDA Pro. It worked, and it was a lot easier than expected. So a little bit of the technical details in terms of what it supports:

The bottom slot connects to the full eight lanes of PCIe gen3 that connects directly to the CPU. I found this being the best bet as it's simple and it will work with my HBA card. And the top x4 slot is connected to the PCH. Although it is only electrically x4, I did make sure to use a connector that has an open end, so you can stick a larger card in there. However, it will still be limited to X4 speeds, and it will be shared with the PCH for bandwidth.

Of course followed all the best practices in terms of getting the correct layer stack, impedance control, and trace matching with correct spacing. Tested everything by hammering both my HBA card and my Mellanox Connectx-4 for about a full day by backing up my other truenas sever. 

Additional parts:

7x M3x20mm screws

2x M3x8mm screws

2.5mm "Flexible light pipe" (you can buy them off amazon)

Noctua 60mmx15mm FAN. 

Around 950g and 22 hours of printing in PETG. 

The files :)

As for the construction :

There is a total of four pieces to print out. The primary body, it is a all in one print. It is capable of being printed within the bed of a mk3/4/ONE. The front of the computer is modeled as a solid. And within the slicer, you can add in a modify box, use a modifier box to make sure you have zero top layers and zero bottom layers. And switch the infield to about 40 to 60%. Make sure the box fills in the front area that will allow the airflow. And you can slice that appropriately. For the info pattern I selected triangles, but this is the fun part, you can select whatever pattern you like. The only thing to keep in mind is that the light pipe holes need to be connected in a solid way. Along with the small alignment box for the power button. 

Customize the front pattern by changing the infill pattern. :)

Now you do this for the Rear panel as well. Finally print the button with the face down and add some supports and thats all you need.  (i will share the 3MF file as well)

Next assembly:

Push in the light pipe all the way into the end of the button. then cut it flush in the front. 

Get the body of the case, and we will be inserting two light pipes. the one close to the bottom will be the activity LED,  (this will be a 42mm length). So cut that and insert it into the hole.  Try and make it flush with the face of the case. 

Next is the Red LED for the lenovo dot. And this will be cut to 46mm Length. 

Grab the riser card, inset the bottom PCIe card. Then press it down into the PC, and screw in the two screws for the riser. ( In my PCB design, i added the second screw hole others do not use, as i wanted to make sure it does not flex under the weight of two cards.)

Next, assemble the fan on the fan bracket. screw down the screws that are normally provided in the Noctua fan kit.  Keep note on how the fan wire is rotated to then go on the inside of the plastic. 

Next bring in the PC, we will attach the fan connector to the connector on the riser card. it goes in between the two cards. 

Place the second card in. 

We will be placing the whole fan shroud and air guide into the PC. There are three points we need to align. Once it drops in easily, you can use a single M3x20mm screw to hold it down. 

Slide in the button into the front of the case by hand and slide in the PC after it. 

Now you can align up the back panel and screw in the two M3x20mm screws into the back. This will pull the PC into the back plastic and hold it as if the PC and the back are one solid piece. 

Next, we add the four screws to hold the body and the back panel together. Here you will be screwing into plastic, so just be careful to not to over tighten. We purposely use long screws here in order to get as much grip in the plastic as possible. 

Finally, we added the two M3x8mm screws that will hold the two PCIe brackets to the back panel. Make sure to align these so that they're parallel with each other. And also make sure that they are fully bolted down to avoid any potential movement.

And thats it! if you ever have to do any work inside the PC. just remove the four corner screws and the PC will come out as one unit. 

OH! and do not forget to remove the bottom cover that would normally cover the NVME ports. this helps with even better airflow as the front fan does blow a bit at the bottoms as well. 


Final photos of the assembly on a deskPi 10" rack. (Dont mind the bottom. will be a future post on a 4 bay 3.5 bay with custom backplane).

Tags