1 / 4
Densium 4 Plus V2 custom front panel — image 1
1 / 4

Densium 4 Plus V2 custom front panel

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Ventilated front panel using 2x 80mm fans and reusing the original button and USB-C connector.

Rating
0 / 5
Likes
6
Downloads
36
Makes
0
Views
346
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

Intro, yapping and temperatures.

Quick disclaimer: the bottom fan isn't sitting fully straight in the photos (fan casing visible at the top of the hole), this is fixed in the released 3MF and STEP files!

When I bought the case, I really liked the wood panel, but after some time I wanted to give it a bit of a different look, so I designed this front panel with room for 2x80mm fans. It's a pretty tight fit with my PowerColor 9060XT Reaper, so might have to measure first to see if it will fit.

I mainly did this because I like the look of it, the exposed fans give it a bit of an "industrial" look, maybe be careful with this if you have kids and/or animals around. But now to the elephant in the room, does it help in any way with temperatures?
Yeah, a bit. I did some quick Furmark runs on the 9060XT and Crucible stress tests on the CPU (8700F) both in stock configuration and with the fans installed and connected. The GPU idle temperature went down from 57°C to 45°C. Temperatures during Furmark went down from 71°C to 68°C (Max. Temp), 94°C to 86°C (Junction) and 80 to 75°C (Mem). The CPU would still hit 95°C during the stress test, but it would take a tiny bit longer to do so, but I doubt any extra fans will help with the tiny Thermalright X36 cooler on the 8700F. (If you're wondering about the CPU choice, I ran this in a different case without a GPU before) Idle temperatures dropped a good 5°C.
Additionally, the nvme temperatures also went down by a handful of degrees, sadly, system monitor in Bazzite wouldn't show me any temperatures for the RAM, or if it did, it didn't label them properly.

This will specifically fit the Densium 4 Plus V2, I don't know if it will fit any of the other variants of the case.

Bill of materials.

Things you will need to source:

  • roughly 60g filament, depending on your settings

  • 14 heat-set inserts (M3x30, I used the ones from CNC Kitchen)

  • 10 M3x8mm bolts (2x8 for the fans, 2 for the USB-C)

  • 2 80mm fans

  • Fan cable Y- splitter depending on your fans and motherboard

Things that can be reused from the original panel:

  • 4 M3 countersunk bolts holding the frame to the case

  • USB-C cable

  • start button with nut

Print settings

For my panel seen in the photos, I used the following settings on my Core One L:

  • PET-G CF filament

  • 2 perimeters

  • "only one perimeter on first layer" enabled

  • Hilbert curve bottom fill pattern

  • 15% zigzag infill

  • textured sheet

  • scarf seams on all perimeters

  • manually adjusted Z-Offset -0.020 as soon as the print started (IMO just makes it look a bit better on the textured sheet)

Assembly

After you finished printing the model, insert all the threaded inserts, put the fans in place, keeping in mind where your fan headers on the motherboard are, unscrewing the fans to rotate them is annoying. :)
Insert and tighten the M3 bolts like so:

The holes for the fans is 81.5x81.5 so a Noctua Chromax will fit snugly with the silicone pads fitted. You might be able to use longer bolts through the back of the fan, but they likely will interfere with your GPU. Be careful when tightening the bolts or you will end up with an ugly dimple on the front of the panel. (This shouldn't happen with the M3x8, but still, be careful!) 

Proceed to install the USB-C and start button, same procedure as on the stock panel, except that you need 2 M3x8 bolts instead of the silver countersunk ones that came with the case.

Put the front panel on the case, install all 4 countersunk M3 bolts without tightening them fully right away, after all 4 are in, proceed to tighten them.

Connect the fans, USB-C and start button/LED connectors to the motherboard and put the side panels back on, done!

I only printed and tested this with PETG-CF, with other filaments the fitment might not be as perfect, feel free to make adjustments with the STEP file!

Tags