InomataK Food Stocker Filament Dryer
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This is a filament dryer using the Inomata Chemical Dry Goods Storage 6.0 and the IRIS OHYAMA futon dryer.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 2
- Makes
- 0
- Views
- 31
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Accessories
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
[概要]
イノマタ化学 乾物ストッカー6.0とIRIS OHYAMAふとん乾燥機を使ったフィラメントドライヤーです 乾物ストッカーと床面部品は密にかみ合います 組み立てにはM3ねじを使用しますが、自己成型ネジ穴になっていますので、ナットは不要です
[部品表(印刷数量)]
InomataKv3g-AxisBottom_AirEntry.stl x 1
InomataKv3g-AxisBottom_AirExit.stl x 1
InomataKv3g-AxisBottom_BottomPlate.stl x 1
InomataKv3g-AxisBottom_PipeConnector.stl x 1
[部品表(金属部品数量)]
六角穴付き M3 皿ねじ 16mm x 8
[組み立て方法]
床面部品(BottomPlate.stl)に空気取入部品(AirEntry.stl)をM3ねじでねじ止めします
床面部品(BottomPlate.stl)に空気排出部品(AirExit.stl)をM3ねじでねじ止めします
パイプコネクタ部品(PipeConnector.stl)を空気取入部品(AirEntry.stl)にはめ込みます
[利用方法]
乾物ストッカー6.0の上面の蓋を外して、フィラメントスプールを入れます
乾物ストッカー6.0の床面の蓋を外して、組み立てた床面部品にはめ込みます
ふとん乾燥機のパイプを、パイプコネクタにはめ込みます
ふとん乾燥機の温風温度、乾燥時間を設定後、開始ボタンでフィラメントを乾燥させます ・「低温モード」にすると45°C程度になるので、PLAに利用可 ・「高温モード」にすると50°C程度になるので、PETGに利用可
ふとん乾燥機側の時間は3時間までなので、必要に応じて工程4を繰り返します
[注意事項]
温度が上がりすぎないよう、状況を見ながら、自己責任でご利用ください
本来のふとん乾燥機の利用目的とは異なりますので、結果に関する保証はいたしかねます
ふとん乾燥機メーカーへのご質問はご遠慮いただくようお願いいたします
[対象機材]
イノマタ化学 乾物ストッカー6.0
https://www.inomata-k.co.jp/item_kitchen/%e4%b9%be%e7%89%a9%e3%82%b9%e3%83%88%e3%83%83%e3%82%ab%e3%83%bc/
※ 乾物ストッカー4.0では1Kgフィラメントスプールが入りませんので誤手配にご注意くださいIRIS OHYAMA カラリエ ふとん乾燥機(ツインノズル) FK-W2-W
https://www.irisplaza.co.jp/index.php?KB=SHOSAI&SID=H288494&msockid=28796de56c3b6b1a0c5978636df26ad3
[Overview]
This is a filament dryer using the Inomata Chemical Dry Goods Storage 6.0 and the IRIS OHYAMA futon dryer. The dry goods storage and the base parts fit together tightly. M3 screws are used for assembly, but since the screw holes are self-molding, nuts are not required.
[Parts List (Print Quantity)]
InomataKv3g-AxisBottom_AirEntry.stl x 1
InomataKv3g-AxisBottom_AirExit.stl x 1
InomataKv3g-AxisBottom_BottomPlate.stl x 1
InomataKv3g-AxisBottom_PipeConnector.stl x 1
[Parts List (Metal Parts Quantity)]
Hex socket M3 countersunk screw 16mm x 8
[Assembly Instructions]
Screw the air intake component (AirEntry.stl) to the bottom plate component (BottomPlate.stl) using M3 screws.
Screw the air exhaust component (AirExit.stl) to the bottom plate component (BottomPlate.stl) using M3 screws.
Insert the pipe connector component (PipeConnector.stl) into the air intake component (AirEntry.stl).
[Usage Instructions]
Remove the top lid of the dry goods storage container 6.0 and insert the filament spool.
Remove the bottom lid of the dry goods storage container 6.0 and insert it into the assembled bottom plate component.
Connect the pipe of the futon dryer to the pipe connector. Insert into the futon.
After setting the hot air temperature and drying time of the futon dryer, dry the filament by pressing the start button. • The "low temperature mode" will reach approximately 45°C, making it suitable for PLA. • The "high temperature mode" will reach approximately 50°C, making it suitable for PETG.
The futon dryer has a maximum timer of 3 hours, so repeat step 4 as needed.
[Precautions]
Please use at your own risk, monitoring the situation to prevent the temperature from rising too high.
This is not the intended use of a futon dryer, so we cannot guarantee the results.
Please refrain from asking questions to the futon dryer manufacturer.
[Applicable Equipment]
Inomata Chemical Dry Goods Storage Container 6.0
https://www.inomata-k.co.jp/item_kitchen/%e4%b9%be%e7%89%a9%e3%82%b9%e3%83%88%e3%83%83%e3%82%ab%e3%83%bc/
*Please note that the Dry Goods Storage Container 4.0 will not fit a 1kg filament spool. Please be careful not to order the wrong item.IRIS OHYAMA Kararie Futon Dryer (Twin Nozzle) FK-W2-W
https://www.irisplaza.co.jp/index.php?KB=SHOSAI&SID=H288494&msockid=28796de56c3b6b1a0c5978636df26ad3
Print Settings
Printer Brand:Biqu
Printer:Biqu B1
Rafts:No
Supports:No
Resolution:0.15mm
Infill:30%
Filament: Tinmmory PETG BLACK
Category: Gadgets