FilamentSpoolHolder for InomataK Dry Food Stocker
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This is a filament spool holder that fits in the Inomata Chemical Dry Storage 6.0.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 5
- Makes
- 0
- Views
- 47
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Accessories
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
[概要]
イノマタ化学 乾物ストッカー6.0に入るフィラメントスプールホルダーです
フィラメントの使用量を極力抑えてありますので、軽量かつ短時間で印刷できます
組み立てにはM3ねじを使用しますが、自己成型ネジ穴になっていますので、ナットは不要です
[部品表(印刷数量)]
InomataKv3g-AxisInner_BottomRing.stl × 1
InomataKv3g-AxisInner_HydrometerHolder.stl × 1
InomataKv3g-AxisInner_SideBeamFenrir.stl × 2
InomataKv3g-AxisInner_TensionBeam.stl × 2
InomataKv3g-AxisInner_SilicaGelPocket.stl × 1
InomataKv3g-AxisSpoolShaft_HexShaft.stl × 1
InomataKv3g-AxisSpoolShaft_HexShaftCap.stl × 1
InomataKv3g-AxisSpoolShaft_ScrewShaftBolt.stl ×1
InomataKv3g-AxisSpoolShaft_ScrewShaftNatLarge.stl × 2
InomataKv3g-AxisSpoolShaft_ScrewShaftNatSmall.stl × 2
[部品表(金属部品数量)]
M3 皿ねじ 8mm x 9
ネオジム磁石 直径3mm、長さ3mm × 6 https://www.hiqparts.com/item/4573211370676.html
ベアリング 6701 (内径12mm,外径18mm、厚さ4mm) × 2 (必須ではありません)
[組み立て方法] ステップ1:スプールホルダー
床面リング部品(BottomRing.stl)に二つの固定用梁部品(TensionBeam.stl)を仮組します
固定用梁部品(TensionBeam.stl)の間に乾燥剤用部品(SilicaGelPocket.stl)を仮組します
固定用梁部品(TensionBeam.stl)のスプール保持梁(SideBeamFenrir.stl)を仮組します
ネジ穴にM3ネジをねじ込みます
湿度計枠部品(HydrometerHolder.stl)を床面リング部品に取付け、M3ねじで固定します
スプール保持梁(SideBeamFenrir.stl)に外側がN極になるようネオジム磁石を圧入します
ステップ2:スプールシャフト
スプールシャフト心棒(HexShaft.stl)のバリをヤスリ等で研磨して滑らかにします
スプールシャフトキャップ(HexShaftCap.stl)のバリをヤスリ等で研磨して滑らかにします
スプールシャフトねじ棒(ScrewShaftBolt.stl)の中心の穴を丸ヤスリ等で研磨して滑らかにします
スプールシャフト心棒(HexShaft.stl)の両端に外型がN極になるようネオジム磁石を圧入します
スプールシャフトキャップ(HexShaftCap.stl)に外側がN極になるようネオジム磁石を圧入します
[組み立て上の注意事項]
ネオジム磁石の極性は外側をN極と記載していますが、方向を一致させることが重要であり、S極が外側でも構いません
ネオジム磁石の極性を間違えた場合は、各部品からネオジム磁石を押し出すことで再利用が可能です
ネオジム磁石を押し出した部品は、磁石が抜けやすくなりますので、ネオジム磁石を接着剤を固定してください
[Overview]
This is a filament spool holder that fits in the Inomata Chemical Dry Storage 6.0.
It minimizes filament usage, so it’s lightweight and can print in a short time.
M3 screws are used for assembly, but the screw holes are self-tapping, so nuts are not needed.
[Parts List (Print Quantity)]
InomataKv3g-AxisInner_BottomRing.stl × 1
InomataKv3g-AxisInner_HydrometerHolder.stl × 1
InomataKv3g-AxisInner_SideBeamFenrir.stl × 2
InomataKv3g-AxisInner_TensionBeam.stl × 2
InomataKv3g-AxisInner_SilicaGelPocket.stl × 1
InomataKv3g-AxisSpoolShaft_HexShaft.stl × 1
InomataKv3g-AxisSpoolShaft_HexShaftCap.stl × 1
InomataKv3g-AxisSpoolShaft_ScrewShaftBolt.stl × 1
InomataKv3g-AxisSpoolShaft_ScrewShaftNatLarge.stl × 2
InomataKv3g-AxisSpoolShaft_ScrewShaftNatSmall.stl × 2
[Parts List (Metal Parts Quantity)]
M3 countersunk screw 8mm x 9
Neodymium magnet Diameter 3mm, Length 3mm × 6 https://www.hiqparts.com/item/4573211370676.html
Bearing 6701 (Inner diameter 12mm, Outer diameter 18mm, Thickness 4mm) × 2 (Optional)
[Assembly Instructions]
Step 1: Spool Holder
Temporarily assemble two fixing beam components (TensionBeam.stl) on the floor ring component (BottomRing.stl)
Temporarily assemble the desiccant component (SilicaGelPocket.stl) between the fixing beam component (TensionBeam.stl)
Temporarily assemble the spool holding beam (SideBeamFenrir.stl) for the fixing beam component (TensionBeam.stl)
Screw in the M3 screw hole
Attach the hygrometer frame component (HydrometerHolder.stl) to the floor ring component and secure it with M3 screws
Press-fit a neodymium magnet into the spool holding beam (SideBeamFenrir.stl) so that the outside is an N-pole.
Step 2: Spool shaft
Spur the burrs on the spool shaft mandrel (HexShaft.stl) and smooth them with a file, etc.
Spur the burrs on the spool shaft cap (HexShaftCap.stl) with a file or similar tool to smooth them
Polish the center hole of the spool shaft screw rod (ScrewShaftBolt.stl) with a round file or similar to smooth it outward.
Insert neodymium magnets into both ends of the spool shaft mandrel (HexShaft.stl) so that the outer shape is N-pole.
Insert neodymium magnets into the spool shaft cap (HexShaftCap.stl) so that the outside is N-pole.
[Assembly Notes]
The polarity of neodymium magnets is labeled as the N pole on the outside, but it is important to align the directions; the S pole can be on the outside.
If the polarity of the neodymium magnet is incorrect, you can reuse it by pushing the magnets out of each component.
Parts where neodymium magnets are pushed out tend to lose their magnets, so fix the neodymium magnets with adhesive
Print Settings
Printer Brand:Biqu
Printer:Biqu B1
Rafts:No
Supports:No
Resolution:0.15mm
Infill:30%
Filament: Tinmorry PETG Galaxy Jewel Blue
Category: Gadgets