Solarcam analoge photography of the sun with a pinhole camera
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Solarcam analoge photography of the sun with a pinhole camera
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 6
- Makes
- 0
- Views
- 100
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Physics & Astronomy
- License
- Creative Commons — Attribution
Solarcam analoge photography of the sun with a pinhole camera.
This Solarcam makes long duration exposure possible because it uses a pinhole and therefor can make a photo with exposures of months. See photo's for examples of possibilities.
This model is meant for placement on a roof with (European) roof tiles (concrete or ceramic). It is also possible to place the solarcam body on a pole with straps through the holes at the back.
The Solarcam is designed for 10x15 cm photo paper. Do not use inktjet photo paper but paper that is meant for analoge photography in a dark room. This paper is used to make a paper photo from a negative film. I used "Foma Fomaspeed Variant 312 Multigrade Matt" but others work as well.
Recommended
After printing pierce the pinhole with a small needle to make sure the hole is open. When there is a thin layer inside the pinhole the photo will be dark or maybe nothing will appear.
Between 21 june and 21 december the sun makes a full cycle from highest to the lowest arc above the horizon. A photo during this period will make the most lines on the photo and probably the best photo.
Before attempting to make long duration photo's you should test the Solarcam on a sunny day.
Practise with the settings of a flatbed scanner.
Don't let you scanner make a preview scan. This will decrease contrast on the photo because the scanner puts a lot of light on the photo for the preview.
Don't develop the photo like you need to do in analoge photography. This photo is scanned once and then edited digitally.
You don't need to place and remove the photography paper in complete darkness or red light. I recommend low light conditions and avoid direct sunlight or a bright light.
Place the Solarcam on/at a solid place where the Solarcam can't move during exposure.
Please be carefull with placing the Solarcam on hard to reach places like trees, poles or roofs. A photo is not (!) worth your life nor limbs.
Don't expect a "perfect" photo like we are used to with a mobile phone. There will be imperfections like water, dust in the Solarcam body, dubbele exposure caused by movement during exposure, unexplanable spots. But this makes this kind of photography more natural and like life itself.
Don't use PLA. My first prototype was printed in PLA and worked well. But in the sun the cap deformed in the heat of the sun.
Remove supports inside the Solarcam body carefully. Obstructions inside the body will make shadows on the photo.
Look for loose strands of filament in the body. On some photo's here you can see some black lines which is filament.
There are different lengths of support beams (steunbalk in Dutch, see file name) and holes in the body so your ideal inclination can be achieved.
Printer settings
More walls will make a more stable shape than higher infill. 4 perimeters is plenty.
I used a 0,6 mm nozzle with 0,35 mm layer height
Outer perimeters first (the pinhole itself is printed first for more accurate pinhole.
Use supports for the Solarcam body. Use tree supports inside the body but preview the layers for supports inside the cone and avoid supports close or on top of the pinhole.
Print the body the the flat side on the printbed (otherwise the pinhole might be far too big (don't ask how I know)
Workflow
Collect materials (bolts, heat inserts, photography paper)
Print the parts, insert the heat inserts, place bolts and assemple the Solarcam
Place the photography paper in low light conditions
Place the for at least one day for a test of the Solarcam and test the workflow including the flatbed scanner
Place the Solarcam with new photography paper for however you like.
Computer: mirror horizontally, invert the colors, enhance what you like (color, contrast, temperature, clarity etc.)
Materials
Black PETG or ASA (the body was ± 350 g and the rest ±200 g of filament). Be careful with ABS/ASA filament because it releases harmful substances. And they stink...
M4 heat inserts
M4 bolts. Different lenghts like 20 mm and long for sidewards stability
Suitable photo paper (this was the hardest part of this project for me, knowing nothing about analoge photography and shops and others not able to help). I ordered at Retrocamera in Belgium (https://www.retrocamera.be/nl)
Photo's
Some examples of finished solar photo's.
One photo which is un-edited. This is how the paper itself looks like straight out of the Solarcam.
Photo's of my roof (up and under)
Details of the Solarcam
Details of the supports inside the Solarcam body
Personal comments
This project is a wish for many years. Having learned a bit of Fusion 360 and having a Prusa 3D printer made it possible.
My design is over-engineered with too thick walls... better safe than sorry was my first requirement.
If you place items like this Solarcam in random public places then there is a chance the police bomb-squad is send on it to dismantle this foreign item. Be wise, please.
Have fun!
Drop a comment if you like this or see possible improvements.