1 / 8
Anycubic ACE Pro Rollenführung mit gekürzten Flügeln/Führungen / Anycubic ACE Pro Filament Spool Guide with Shortened Wings — image 1
1 / 8

Anycubic ACE Pro Rollenführung mit gekürzten Flügeln/Führungen / Anycubic ACE Pro Filament Spool Guide with Shortened Wings

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Anycubic ACE Pro Rollenführung für übervolle Filamentspulen / Anycubic ACE Pro guide for overfilled filament spools

Rating
0 / 5
Likes
9
Downloads
46
Makes
0
Views
501
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

English version below the German description.

Da die Führungen/Flügel beim Original, bei größeren oder zu vollen Spulen an der Rolle schleifen, habe ich nach der Original-Vorlage diese in SketchUp neu gezeichnet und die Führungen/Flügel um ca. 10 mm gekürzt.

Zusätzlich habe ich noch den Drehverschluss des Originals zum einfüllen/entleeren des Silica-Gels, zugunsten eines Schiebers ersetzt. Dies erleichtert das Befüllen/Entleeren. Insgesamt sind vier Schieber dabei. Zwei Schieber haben 0,05 mm Spiel und zwei Schieber 0,1 mm Spiel. Bei mir auf dem Snapmaker U1 gedruckt passen die Schieber mit 0,1 mm Spiel am besten.

Die rechteckige Öffnung für Hygrometer habe ich mit einer runden Öffnung ersetzt, da ich keine neuen Hygrometer kaufen wollte.

Lässt sich auf einer Bettgröße von mindestens 250 mm x 250 mm (z.B. Anycubic Kobra S1) drucken.

Update 2026-07-19

  • Es stehen drei Versionen zur Auswahl, die sich nur im Design der Lüftungsschlitze des Silica-Gel Behälter unterscheiden. In den Bildern sind die Unterschiede gut zu sehen.

Zusammengefasst:

Nach der Original-Vorlage neu in SketchUp gezeichnet mit folgende Änderungen:

  • Flügel/Führungen gekürzt

  • Silca-Gel Behälter mit einem Schieber versehen zum leichteren Befüllen und Entleeren

  • Runde Öffnung fürs Hygrometer.

English Version:

On the original design, the guides/wings can rub against larger or fully loaded filament spools. To fix this, I redesigned the model in SketchUp based on the original design and shortened the guides/wings by approximately 10 mm.

I also replaced the original twist-lock opening for filling and emptying the silica gel with a sliding lid. This makes refilling and emptying the silica gel much easier. The model includes four sliding lids with different clearances. Two have a clearance of 0.05 mm, and two have a clearance of 0.1 mm. On my Snapmaker U1, the 0.1 mm clearance provided the best fit.

Finally, I replaced the rectangular opening for the hygrometer with a round one, as I wanted to continue using my existing round hygrometers instead of buying new ones.

Requires a minimum print bed size of 250 mm x 250 mm (e.g. Anycubic Kobra S1).

Update 2026-07-19

  • Three versions are available, differing only in the design of the ventilation openings. The images above clearly show the differences.

Summarized:

Redrawn in SketchUp based on the original design, with the following changes:

  • Shortened the wings/guides.

  • Added a sliding lid to the silica gel compartment for easier filling and emptying.

  • Added a round opening for a hygrometer.