1 / 2
ASUS_PRIME_Z370-P_Z370-P-II_IO_Shield_with_snap_border — image 1
1 / 2

ASUS_PRIME_Z370-P_Z370-P-II_IO_Shield_with_snap_border

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

ASUS_PRIME_Z370-P_Z370-P-II_IO_Shield_with_snap_border

Rating
0 / 5
Likes
0
Downloads
11
Makes
0
Views
23
Reviews
0

Updated at source:

Model information

Category
Accessories
License
Creative Commons — Attribution — Share Alike

Join both models, z370 holes with the snap border from z270. To be validated yet.

ASUS PRIME Z370-P / Z370-P II — 3D-Printed Rear I/O Shield

Technical description

Custom rear motherboard I/O shield designed for:

  • ASUS PRIME Z370-P

  • ASUS PRIME Z370-P II

The model includes the correct rear connector openings and an integrated raised perimeter lip designed to retain the shield inside a standard ATX computer-case I/O opening.

Rear connector layout:

  • 1 × PS/2 keyboard/mouse port

  • 2 × USB 2.0 ports

  • 1 × DVI-D port

  • 1 × HDMI port

  • 4 × USB 3.x Type-A ports

  • 1 × RJ45 Ethernet port

  • 3 × 3.5 mm audio ports

This is a plastic replacement for the original metal I/O shield. It closes the rear opening and supports normal case airflow, but it does not provide the same electrical grounding or electromagnetic shielding as the original metal part.

Final model dimensions

  • Overall width: 160.38 mm

  • Overall height: 46.53 mm

  • Maximum depth/thickness: 3.99 mm

  • Main plate thickness: approximately 1 mm

  • Integrated raised retaining border: approximately 3 mm

  • Recommended nozzle: 0.4 mm

Small dimensional adjustments may be necessary depending on printer calibration and the exact case opening.

Recommended material

PETG is the recommended material.

PETG offers the best balance of:

  • heat resistance;

  • slight flexibility during installation;

  • resistance to cracking;

  • long-term durability;

  • relatively easy printing.

PLA is also acceptable, especially for a normal desktop or home-server case with adequate ventilation.


General printing instructions

  • Print orientation: flat main face against the print bed

  • Raised retaining border facing upward

  • No supports normally required

  • Nozzle: 0.4 mm

  • Layer height: 0.20 mm

  • Wall count: 4

  • Top and bottom layers: 4–5

  • Infill: 20–40%

  • Print speed: 35–50 mm/s

  • Brim: optional, 3–5 mm

  • Estimated material: approximately 9–18 g

  • Estimated printing time: approximately 35–70 minutes

Because the part is thin, most of its structure will be produced from walls rather than infill.

Material-specific instructions

PETG — Recommended

PETG is the preferred permanent material because it can flex slightly when being inserted into the case without cracking easily.

Suggested settings:

  • Nozzle temperature: 230–245 °C

  • Bed temperature: 70–85 °C

  • Layer height: 0.20 mm

  • Cooling fan: 30–60%

  • Print speed: 35–45 mm/s

  • Walls: 4

  • Infill: 25–40%

  • Brim: recommended if the corners tend to lift

Installation notes:

  • Allow the part to cool completely before removing it from the bed.

  • Remove stringing around the USB, HDMI and audio openings carefully.

  • PETG may grip the bed strongly, so avoid excessive first-layer compression.

  • Do not force the shield into the case if the retaining lip is too tight.

PETG is suitable for normal gaming PCs, servers and systems that operate for long periods.

PLA / PLA+

PLA is suitable for test prints and may also be used permanently in a normally ventilated case.

Suggested settings:

  • Nozzle temperature: 195–215 °C

  • Bed temperature: 50–65 °C

  • Layer height: 0.20 mm

  • Cooling fan: 80–100% after the first layers

  • Print speed: 40–55 mm/s

  • Walls: 4

  • Infill: 20–35%

  • Brim: normally optional

Installation notes:

  • PLA is rigid and may crack if the border is forced into the case.

  • Insert one long edge first and press the opposite edge gradually.

  • Do not bend the part sharply.

  • Avoid leaving the shield close to a direct hot-air exhaust.

  • PLA normally works in this location because the rear I/O area should remain considerably cooler than the CPU itself.

PLA is the easiest option and is appropriate when PETG is unavailable.

ABS

ABS offers better temperature resistance than PLA but is more difficult to print accurately.

Suggested settings:

  • Nozzle temperature: 235–255 °C

  • Bed temperature: 90–110 °C

  • Layer height: 0.20 mm

  • Cooling fan: 0–20%

  • Print speed: 35–45 mm/s

  • Walls: 4–5

  • Infill: 25–40%

  • Brim: 5–8 mm

  • Enclosure: strongly recommended

Installation notes:

  • Print inside an enclosed printer to reduce warping.

  • Allow the print and enclosure to cool gradually.

  • Check the external dimensions after printing because ABS can shrink.

  • Slight X/Y scaling may be required to compensate for material shrinkage.

  • Ensure adequate ventilation while printing due to fumes.

ABS is technically suitable, but PETG is normally easier and more dimensionally predictable for this part.

ASA

ASA provides similar mechanical and heat resistance to ABS with improved environmental and UV resistance.

Suggested settings:

  • Nozzle temperature: 240–260 °C

  • Bed temperature: 90–110 °C

  • Layer height: 0.20 mm

  • Cooling fan: 0–20%

  • Print speed: 35–45 mm/s

  • Walls: 4–5

  • Infill: 25–40%

  • Brim: 5–8 mm

  • Enclosure: required or strongly recommended

Installation notes:

  • Allow the part to cool slowly before opening the enclosure.

  • Inspect for corner lifting or dimensional shrinkage.

  • Test-fit before installing the motherboard.

  • Print in a properly ventilated area.

ASA is durable but offers little practical advantage over PETG for an indoor computer case.

Polycarbonate

Polycarbonate is extremely strong and heat resistant but unnecessary for this application unless it is already available.

Suggested settings:

  • Nozzle temperature: 260–300 °C

  • Bed temperature: 100–120 °C

  • Layer height: 0.20 mm

  • Cooling fan: off or very low

  • Walls: 4–5

  • Infill: 30–50%

  • Enclosure: required

  • Dry filament before printing

Polycarbonate requires a suitable all-metal hot end, heated enclosure and appropriate build surface. PETG is more practical for this component.

Materials not recommended

TPU

TPU is generally too flexible. The plate may move when cables are inserted or removed and may not hold securely in the case opening.

Nylon

Nylon can work but normally absorbs moisture, may warp and can be too flexible for a thin I/O shield. It provides no important advantage over PETG here.

Test fitting and dimensional adjustment

Before installing the motherboard:

  1. Test the shield in the empty case opening.

  2. Confirm that the PS/2 opening is on the left and the three audio openings are on the right when viewed from outside the rear of the case.

  3. Confirm that the raised retaining border faces inward toward the motherboard.

  4. Check that the shield sits flat without bowing.

  5. Install the motherboard only after the shield fits correctly.

Do not force the part. Excessive pressure may crack PLA or distort the case opening.

For a slightly tight fit:

  • Scale X and Y to 99.5–99.8%

  • Keep Z at 100%

For a slightly loose fit:

  • Scale X and Y to 100.2–100.4%

  • Keep Z at 100%

Adjust in small increments because a change of 0.5% represents approximately 0.8 mm across the full width.

Recommended production specification

For a printing service, use:

Print in black PETG using a 0.4 mm nozzle, 0.20 mm layer height, four perimeter walls, five top and bottom layers, 30% infill, no supports, with the flat face placed on the build plate and the raised retaining border facing upward. Dimensional accuracy should be within ±0.20 mm.