1 / 11
6/10 Port Siren "Decot Model DT-16" — image 1
1 / 11

6/10 Port Siren "Decot Model DT-16"

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

My first siren model I made myself! This is entirely made in Tinkercad.

Rating
0 / 5
Likes
5
Downloads
10
Makes
0
Views
121
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

The Decot Model DT-16 is a fictional siren, but a mix of a D.E.W. 6/10 prototype and a 5T. The Decot part of the name is from the port ratio. The DT (Dual Tone) comes from the T in 5T, the 3 main vanes on the rotor, and Model in the name.

Check out my personal build testing!

Here it is! My first siren model I've ever made myself and released to the public. Below I'll include the information like what motors are compatible, wiring, assembly, updates, ect. Be sure to let me know if you come across any issues or and I'll be quick to fix it! Same with questions, feel free to shoot me a message on Discord or here on Printables if you have any questions! By the time this releases I will have ether finished or am near finishing my personal build so most issues should already be tackled.

Shoutout to Haroldhihat for allowing me to use his cooling fan on my model!

Minimum printer bed size: 256x256x256mm

*BE SURE TO READ THE FULL DESCRIPTION IF YOU ARE UNEXPERIENCED WITH MAKING MINI SIRENS*

UPDATES:

9/10/2026: Updated files are now starting to be added, such include: Shortened stator (to reduce time to print and filament cost), weighted & couplered rotors, more photos, seperated the top hat connector to the top half housing core piece for the sake of supports/reliability when printing, and added a mount

9/24/2026: Replaced the mount plate with a version with cutouts to make it easier to align the little mount legs.


MOTOR:

Compatible motors for this model include: all 250-255w motors. Ribbed or flatface, stator and motor cover has holes for both kinds. I wouldnt recommend using a motor under 195w as it may run underspeed due to the large impeller. My personal unit uses a Samsung DE31-00028P because its the only motor I had at the time of making the siren. You can use any motor you want, but fair warning too low of wattage will result in underspeed and possibly other issues, 29G, 29H, and 29K are all recommended.

https://bit.ly/41hs4ox REFER TO THIS MOTOR CHART BY DEMETRIUS IF YOU ARE UNAWARE OF WHAT MOTOR YOU MAY NEED! If you are looking to buy a motor go to eBay and search the model of what motor model you want and double check the listing is correct so you dont get the wrong one.

HARDWARE/REQUIRED PARTS:

Cable: https://a.co/d/0avXjbPG

Capacitor (I recommend 10uF, especially for the weighted version): https://a.co/d/02ju7x4b

M4 Screws: https://a.co/d/08dwhbbW
(Side note for the screws: I based basically almost every screw (aside the core screws) to use M4's so you dont need to buy multiple different sets. Although if you want to bolt screws into the housing for screens, use M3's. Wood screws could also work, whatever you want to do).

M3 Inserts: https://a.co/d/062EeyqV

M3 Screws: https://a.co/d/08hsPz0N

Coupler: https://a.co/d/06ranPK9

Weights: https://a.co/d/0iosjQCX 
(For weights: You need 18 for the weighted rotor, so buy a 2 pack of the slotted weights. Each hanger holds 9).

PRINTING:

ROTOR: On the rotor you see there is a cutout/keyway in the shaft hole, thats for the seam. Since having the seam bumps can cause wavy and wobbly rotors I added that keyway. So in your slicer you can use the seam paint tool and draw the line straight down that cutout so it focuses the seam there and doesnt disturb where the shaft presses through. You will see there are many rotor files too, the mm listed is the shaft hole diameter. I added many so based on what your printers tolerances are you can download the one that works best. Couplered rotors are the same way, focus the seam in the keyway and it should reduce any rotor wobble/wave.

STATOR: The seam and whatnot doesnt matter on this, though I recommend a brim as said in the file description so it doesnt warp, I've had warp issues so I recommend a brim. Do print with supports also. Printing orientation is already set in the STL so just import the file and you are good to go!

MOTOR COVER: Seam doesnt matter on the cover, but a brim I recommend so it doesnt warp. Supports obviously, infill doesnt entirely matter so set that to your hearts content. Print orientation is already fine in the STL, just import and edit your settings.

COOLING FAN: I recommend 100% infill, pattern can be any, I used concentric. Supports if you want, I used supports. If your printer bridges good then supports aint needed. Brim is optional, I would to reduce warp if thats an issue for you.

HOUSING: Most of the parts I heavily recommend high infill so you get strong housing parts and reduce the risk of print failures. Also use supports for the parts that require supports, excluding the hat quarter pieces. The housing quarter pieces are probably the hardest parts to print, due to the absurd angle, I apologize for that. Supports wont do a lot for you there ether.

WIRING:

For wiring the cable, clip the female end off the cable and cut back the insulation so you can get access to the bare wires. Then wire the line wires from the motor to the cable. Most Samsungs have brown and white wires as line wires, but refer to the electrical wiring diagram on the blower fan housing to know what wires are line. Then for wiring the capacitor, wire the capacitor wires to the capacitor. Again some Samsungs it isnt the same as others but the usual color is red and orange.

ASSEMBLY:

If you dont like word-form instructions, I have an assembly video going over practically everything! Any other questions? Comment on my video or DM me! heres a direct link to the video: 

CORE: After you have the bare motor and took off the blower fan assemblies, screw the stator on the side the wires DO NOT come out from. Now try pressing the rotor on, you may endure scraping/chaffing issues initally, to fix that ether reposition the stator if its an uneven tolerance or do some sanding and it should fix your issue.

MOTOR COVER: After you get the core working and spinning problem free, slide the motor cover on the motor, making sure the longer end covers over the whole motor.

COOLING FAN: Slide the cooling fan on the other shaft with the coupler and get it screwed in, making sure the intake side of the fan is facing the windings. If the fan wobbles or waves it isnt a giant issue, just try to avoid gluing the coupler on wonky.

BOTTOM PLATE: Simply screw it on the bottom of the motor cover and screw it shut, making sure the side with the dimple is toward the shaft to give it extra clearance.

HOUSING: For the core of the housing, simply plastic weld the top half to the bottom half with a soldering iron, I added 3 rectangle cutouts to hopefully make lining everything up a little easier, and to ensure you get perfectly lined up square cutouts too. With the shroud pieces, plastic weld the 4ths together in the correct orientation. Make sure you have 6 properly lined up holes too so you can bolt the hat to the housing core. Same story with the bottom shroud, plastic weld all 4 sections and make sure you have 6 properly spaced and even holes. If you print the top hat connector piece seperate, just line up the holes as close to the middle of the housing piece (not the opening, look at my housing photos for reference) and weld it to the top half. This is to ensure the screws line up when you assemble the housing. Same story with the bottom half.

MOUNT (optional): If you print my little stand/mount, it requires M3 inserts and M3 screws. For the inserts stick 4 in the legs where the hole is (non rigid side first) and with a hot soldering iron slowly press it into the leg until its in there all the way. Do that 4 times for every leg. after screw the legs to the plate with M3's. pretty straight forward.

Once you complete your personal build, make a post or send me some photos of yours! I'd be pleased to see and hear yalls personal makes!

Tags