1 / 8
Amphora Pen Pot — Panathenaic Prize Amphora, Engraved Bands, No Supports — image 1
1 / 8

Amphora Pen Pot — Panathenaic Prize Amphora, Engraved Bands, No Supports

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A Greek amphora as a desk pen pot: running-athlete frieze, Greek-key meander, ray and palmette bands

Rating
0 / 5
Likes
1
Downloads
3
Makes
0
Views
25
Reviews
0

Updated at source:

Model information

Category
Office
License
Creative Commons — Attribution

A Greek amphora that works as a desk pen pot. The decoration is not a texture wrapped on afterwards — the four bands of a Panathenaic prize amphora are cut into the wall as real 0.7 mm geometry.

The printed pot

One part, upright, no supports. Every outer section transition on the profile is under 45°, including the pierced handles.

The engraving follows the curve. Each band is cut as the intersection of the motif's radial prism with a 0.7 mm shell of the surface, so the recess is the same depth on the belly and on the neck. A plain radial cut would bite 2 mm deep at the widest point and miss the wall entirely up at the neck.

The foot is deliberately wrong. The museum piece — Panathenaic prize amphora, Euphiletos Painter, ca. 530 BC — stands on a ~16 mm foot under a 53 mm belly, which tips the moment a pen leans. Here the foot is Ø34 with a solid 8 mm base slab. Measured off the mesh, the tilt at which the centre of mass crosses the foot edge:

  • Ø34, this model: 20.5° empty, 14.1° holding ten pens

  • Ø16, faithful to the original: 10.0° empty, 6.8° holding ten pens

Roughly double the margin, which is what makes it a pot you can use rather than a display piece.

Decoration

  • 6-athlete running frieze on the belly

  • Greek-key meander below it

  • ray/tongue bands at the shoulder and above the foot

  • palmette and bead band on the neck

  • incised ground lines throughout

Render, front

Three ways to finish it

  1. Gradient or silk filament — the photos are a single gradient PLA print, no paint, no AMS. The bands sit at different heights, so a colour-shifting filament gives each one its own tone for free.

  2. Terracotta + black acrylic — wipe black paint across the bands, wipe the raised surface clean before it dries. The paint stays in the 0.7 mm recesses. This is what the engraving depth was sized for, and it reproduces true black-figure decoration.

  3. AMS two-colour — amphora_pen_pot_decor.stl is the exact chip volume the engraving removes. Import it together with the pot and answer Yes to "load as a single object with multiple parts?". Do not use Split to Parts: it splits by connected component, and the decoration is 113 disjoint islands, so you would get 114 parts.

Print settings

  • Ø55 × 105 mm (71.5 mm across the handles), about 39 g

  • Upright as exported, no supports, no brim needed

  • 0.2 mm layers, 3 walls, 15–20 % infill

  • 0.4 mm nozzle. A 0.6 mm nozzle cannot resolve the meander.

  • Do not scale below 100 % — the engraving stops reading under 0.6 mm

The full print guide is above, and amphora_pen_pot.scad is the parametric source: height, athlete count, frieze position, meander repeats, engraving depth and handle width are all variables at the top of the file. The body is a Catmull-Rom spline through the wall profile, so it can be reshaped without producing facet bands.

Not watertight — 2 mm printed walls, so no water and no cut flowers. Drop a glass test tube in if you want a bud vase.

Ancient Greek pottery is public domain. This is an original CAD design of a museum motif, not merchandise for any film, game or brand.

Tags