1 / 8
Tilting mount for a portable monitor— tripod leg — image 1
1 / 8

Tilting mount for a portable monitor— tripod leg

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

No-VESA portable monitor on a tripod leg, -30 to +30 tilt. PETG, 19 parts.

Rating
0 / 5
Likes
0
Downloads
1
Makes
0
Views
37
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

What it is

A mount that carries a portable monitor on one leg of a photo tripod and lets it tilt from -30° to +30°, continuously. The monitor needs no VESA pattern: it sits in the frame.

Prototype status — testing in progress: this model is still being validated through printing, assembly and real-world use. Dimensions, settings and minor details may change after test results. Verify the real monitor size and mass, then test retention and tilt progressively over a protected surface.

It is a panel: a clamp pressing on the side edges cracks it, and the side edges are also the one place you must not touch, because that is where the USB ports and the buttons are. So the monitor rests: a shelf the full width to stand on, two posts behind the screen, and a crossbar on top with two hooks that go over the upper edge and come down 10 mm at the front. The whole lower band stays open.

Which monitors fit

  • width from 238 to 426 mm

  • height from 235 to 280 mm, covered by 45 mm of slot on the crossbar

  • thickness up to 18 mm

  • mass up to 1.85 kg — not generic caution: it is the upright's bending, solved for mass

A friction clutch holds the tilt

Two flat rings face each other, one on the upright and one on each fork, squeezed by two knobs. Back the knobs off, pick the angle, tighten: the tilt is continuous, not indexed. The clutch holds 6.3 N·m against the 2.9 N·m the monitor makes when you push on its top edge.

Every screw you touch in the field is hand-tightened: the knobs on the leg clamps and the two on the clutch have a hex head captured inside them, and no key is needed to put the mount on the tripod or to change the tilt.

It clamps on the leg

Round tube, Ø 31.75 mm — the same clamp as the onStep case, so the two live on the same tripod.

What you print

  • P_UPRIGHT ×1 — upright, the spine that carries everything (303 cm³, 70 × 60 × 245 mm)

  • P_CRADLE ×1 — cradle frame: back plate and base, carries the shelf (172 cm³, 180 × 44 × 121 mm)

  • P_FORK_RIGHT ×1 — right fork: friction cheek and arm (71 cm³, 181 × 134 × 12 mm)

  • P_FORK_LEFT ×1 — left fork, same but mirrored (71 cm³, 181 × 134 × 12 mm)

  • P_SHELF_RIGHT ×1 — right half of the shelf the monitor stands on (129 cm³, 213 × 39 × 83 mm)

  • P_SHELF_LEFT ×1 — left half of the same shelf (129 cm³, 213 × 39 × 83 mm)

  • P_POST_RIGHT ×1 — right post, behind the screen (53 cm³, 28 × 8 × 245 mm)

  • P_POST_LEFT ×1 — left post, behind the screen (53 cm³, 28 × 8 × 245 mm)

  • P_CROSSBAR ×1 — top crossbar with the two hooks (158 cm³, 238 × 56 × 78 mm)

  • P_BRACKET_UPPER ×1 — upper leg bracket, with the arm (72 cm³, 66 × 75 × 35 mm)

  • P_BRACKET_LOWER ×1 — lower leg bracket, with the arm (42 cm³, 66 × 44 × 35 mm)

  • P_CLAMP_UPPER ×1 — upper clamp half (24 cm³, 66 × 25 × 21 mm)

  • P_CLAMP_LOWER ×1 — lower clamp half (24 cm³, 66 × 25 × 21 mm)

  • P_TILT_KNOB ×2 — tilt knob (11 cm³, 34 × 34 × 14 mm)

  • P_CLAMP_KNOB ×4 — hand knob for a leg-clamp screw (8 cm³, 28 × 28 × 16 mm)

  • P_LOCK_KNOB ×2 — hand knob that locks the crossbar (8 cm³, 28 × 28 × 16 mm)

21 printed parts, 1367 cm³ of PETG. The largest part is 245 mm, and every mesh is already laid on the face it prints on.

Printing

The reference setup is PETG, 0.60 mm nozzle and 0.30 mm layers. Start with 5–6 walls, 6 top and bottom layers and 45–55% gyroid infill for the upright, cradle, forks, brackets and clamp jaws. Four to five walls and 40–50% gyroid are a suitable starting point for shelves, posts and the crossbar. Use 5 walls and about 50% gyroid for the knobs.

The longest part is 245 mm: check the printer's real usable area and leave room for a brim. Keep supports out of insert pockets, channels and clutch faces. These are starting values to validate on the actual printer; wall count and orientation carry more load than infill.

What you buy

Brass heat-set inserts and screws, nothing else — no bolts, no nuts to hold with a second spanner. The quantities come from the model, counted seat by seat.

  • 6 × brass heat-set insert M4

  • 16 × brass heat-set insert M5

  • 2 × brass heat-set insert M6

  • 4 × socket head screw M4 × 16 ISO 4762

  • 2 × hex head screw M4 × 20 ISO 4017 — these are the ones captured in the printed knobs

  • 8 × socket head screw M5 × 12 ISO 4762

  • 4 × socket head screw M5 × 25 ISO 4762

  • 4 × hex head screw M5 × 30 ISO 4017 — these are the ones captured in the printed knobs

  • 2 × hex head screw M6 × 25 ISO 4017 — these are the ones captured in the printed knobs

48 pieces of hardware in all. Buy a few spares of each: an insert set crooked is thrown away.

What is verified on the model

  • parametric chain: 17 checks, all with margin

  • every printed part is one valid solid, and no pair of parts occupies the same space

  • the screws are drawn, not just counted: none bottoms out in its seat before the head seats, and each one bears on a part

  • around every insert the wall the maker asks for is there, and it is all in the part that carries the insert

  • every part, in the pose it prints in, fits the bed

  • the frame and the monitor's own envelope are swept through the whole tilt range against the upright, the clamps and the leg

Tags