1 / 8
Playmobil Steck Castle Arched Window Frame 3007690 (30076900) - 3666 Replacement Part — image 1
1 / 8

Playmobil Steck Castle Arched Window Frame 3007690 (30076900) - 3666 Replacement Part

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a 3D-printable replacement for PLAYMOBIL part 3007690 / 30076900

Rating
0 / 5
Likes
4
Downloads
24
Makes
0
Views
93
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

PLAYMOBIL Steck Castle Arched Window Frame – Part 3007690 / 30076900

This is a 3D-printable replacement for PLAYMOBIL part 3007690 / 30076900, the small arched window frame used in the classic PLAYMOBIL Steck castle construction system.

The original part can be found in vintage medieval castle sets such as PLAYMOBIL 3666 and is also compatible with other classic castle and medieval sets that use the same wall system.

I tried to reproduce the original part as closely as I could, including the arched profile, frame shape and mounting features. Because I kept the geometry as close to the original as possible, the model cannot be printed reliably without supports, so supports should remain enabled when printing.

The dimensions, mounting points and general shape were designed to match the original window frame as closely as possible. Because printer calibration and material shrinkage vary, minor sanding or cleanup of the connection points may occasionally be required.

INCLUDED FILES

  • 3007690.stl – ready-to-slice mesh model

  • 3007690.stp – STEP/STP CAD model for editing or modification in compatible CAD software

  • 3007690.3mf – prepared print project with the recommended orientation and settings

The model is intended to be printed at 100% scale.

FIT AND INSTALLATION

Carefully remove all support material before attempting installation, particularly around the small mounting features.

Test-fit the part gently into the original wall section. If the fit is slightly tight, lightly sand or file only the area causing interference and remove a very small amount of material at a time.

Do not force the printed frame into the original wall section. If the entire part consistently prints too tight or too loose, check filament flow, first-layer calibration and dimensional accuracy before changing the model scale.

This replacement is useful for restoring incomplete vintage PLAYMOBIL castles, replacing broken or missing window frames, completing second-hand castle wall sections and creating custom Steck-System castle layouts.

The download contains the window frame itself only. Original castle walls, window inserts, shutters, figures and other accessories shown in presentation photos are not included.

PART NUMBER

3007690 / 30076900

TRADEMARK NOTICE

This is an independently recreated, unofficial compatible replacement part.

PLAYMOBIL is a trademark of its respective owner. This design is not affiliated with, endorsed by or sponsored by the trademark owner.

3D printing settings

3D PRINTING SETTINGS

For the easiest and most reliable print, use the supplied 3007690.3mf file. It already contains the recommended model orientation and prepared printing settings.

Do not use the slicer's automatic orientation function unless you intend to create your own support strategy.

Because the model was designed to remain as close as possible to the geometry of the original PLAYMOBIL part, supports are required.

RECOMMENDED SETTINGS

  • Printer used for the supplied profile: Bambu Lab A1

  • Nozzle: 0.4 mm

  • Layer height: 0.08 mm

  • Initial layer height: 0.20 mm

  • Wall generator: Classic

  • Walls/perimeters: 2

  • Top layers: 9

  • Bottom layers: 7

  • Infill: 15%

  • Infill pattern: Gyroid

  • Print sequence: By layer

  • Model scale: 100%

  • Supports: Enabled

Use the support configuration saved in the supplied 3MF as the recommended starting point.

SUPPORTS

Do not disable supports for this model.

The original-style mounting and frame geometry creates areas that need support material in the recommended orientation.

After printing, remove the supports gradually and take extra care around:

  • Small mounting tabs

  • Thin frame sections

  • The lower connection features

  • The inside of the arched opening

Avoid twisting large pieces of support material against the frame, as the smaller connection features can be damaged.

Needle-nose pliers, tweezers and flush cutters can be useful for removing support material from tighter areas.

BUILD-PLATE ADHESION

The supplied project uses a brim to help stabilize the relatively narrow part during printing.

Recommended starting settings:

  • Brim width: 5 mm

  • Brim/object gap: 0.10 mm

Clean the build plate before printing and make sure the first layer is properly calibrated.

If the part begins to lift or move during printing, increase the brim width or reduce the brim gap.

MATERIAL

PLA or PLA+ is recommended for this part.

PLA provides good dimensional accuracy, sharp mounting features and relatively easy support removal.

PETG may also be used if slightly greater flexibility is preferred, although PETG supports can be more difficult to remove cleanly.

When using PETG, use an appropriate PETG filament profile rather than the PLA temperatures saved in the supplied project.

FINISHING

Allow the print to cool before removing it from the build plate.

After removal:

  1. Remove the brim.

  2. Carefully remove all support material.

  3. Inspect the mounting features for remaining support material.

  4. Remove any strings or small blobs.

  5. Check the build-plate-facing surfaces for elephant-foot expansion.

  6. Test-fit the part gently.

If a connection point is slightly tight, use a fine sanding stick, file or fine-grit sandpaper to remove a very small amount of material.

If all connection points are consistently too tight or too loose, calibrate filament flow and dimensional accuracy before changing the overall model scale.