1 / 4
Modified Replacement Part for Haworth Fern Office Chair -  Seat Tilt Mechanism Failure — image 1
1 / 4

Modified Replacement Part for Haworth Fern Office Chair - Seat Tilt Mechanism Failure

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A custom designed - re-engineered rail body to replace defective rail mechanism in Haworth Fern Office Chair.

Rating
0 / 5
Likes
1
Downloads
3
Makes
0
Views
95
Reviews
0

Updated at source:

Model information

Category
Office
License
Creative Commons — Attribution — Noncommercial — Share Alike

**Disclaimer: Operating on your chair will very likely void your warranty. I recommend checking if you can get your chair repaired under warranty before attempting a modification.**

**The production and release of this file is for purely personal use and not for resale or patent infringement. All rights are reserved by Haworth INC.**

This mod will remove the tilt functionality of the seat of your Haworth Fern office chair (if you have it).

It will require more screws than are available on the chair itself, I personally purchased these screws from McMasterCarr. (These should work as a suitable replacement)

Thread-Forming Screws For Plastic, M5 Screw Size, 12 Mm Long, 10 Mm Flange Diameter, T20 Torx 96817A332

If you have a Haworth Fern office chair with a defective tilt mechanism (or a chair that's tilting without the purchase of the tilt function). This repair should solve the issue. 

This will remove any tilting function entirely. I personally never used it much anyway. Over time, the indexing mechanism experiences fatigue due to constant load over time, causing the bushing and plastic indexing shaft to disintegrate/gall.

It seems that every Haworth Fern chair use this same rail mechanism and indexing cam/shaft - regardless of whether you purchased the tilt function or not . This means even if you didn't purchase the tilt function, the internal tilt mechanism is still present but without the lever + steel cable to adjust the forward tilt. 

This rail has been changed to effectively mirror the 'horse-shoe' retaining plug that can be seen on the front end of the rail.

 "Indexing Cam Shaft"

I attempted to just print and replace this part that rests on the bushed support pins. I also replaced the sleeve bushings (since the original bushings disintegrated). However, it proved to be ineffective and failed in the same way within a week. (printed in ABS GF 100% infill).

Link to 'indexing cam/shaft' is found here as uploaded by Fellan46 on thingiverse: https://www.thingiverse.com/thing:7320293

Bearing Replacement: https://a.co/d/01oSk4kC

OEM - Right - Rear Seat Rail with Indexing Mechanism

New Design - Rear - Right Side (example of mounting change)



The original plastic used in the OEM injection molded rails is PA6-CF (Nylon with Carbon Fiber)

I recommend printing using an engineering-grade filament with fiber reinforcement to reduce creep and to maintain its dimensional accuracy. IE. PC-CF, PETG-CF, or post processed PA6-CF (if you don't mind conditioning and annealing).

I wouldn't recommend printing this with less than 4 wall loops and less than 50% infill. My test prototypes for test fitting (printed from PETG with only 3-4 wall loops) structurally failed under load.

I believe 3D Hexagon/cubic/gyroid infill would work for this model, I personally printed with 100% infill.

The "stand off ring" is printed separately and glued in place for each rail after printing. This was done in order to have a flat surface for ease of printing and to avoid using a raft. If you plan to glue this in place, use the appropriate adhesive. (ie. cyanoacrylate (super glue) will cause embrittlement in ABS).

I have also modeled replacement plugs for the front of the rail - just in case others may need them - as shown below.

This project is tentatively complete. Out of curiosity, I printed some out of PETG @ 100% infill, and they have held up since ~August 17,  2026. However, I plan to replace them with the PA6-CF ones shown in the picture after some annealing and conditioning to improve toughness and remove potential material creep.

I sincerely hope that any owners of this chair who have shared my struggles will appreciate this work and find it useful.

If you have any questions / concerns, please comment.


Further documentation courtesy of Haworth's website:

Haworth Fern for "Seat Replacement" instructions: 

https://www.haworth.com/content/dam/digital/north-american-assets/technical-documents/installation-instructions/furniture/seating/fern/7029-9976_1.pdf

"Recycling Guide" which shows further disassembly procedures if necessary:

https://www.haworth.com/na/en/design-resources/details.html/content/dam/digital/north-american-assets/haworth-products/seating/fern-family/fern-task/documents/Fern-Disassembly-Recycling-Instructions.pdf

F3D file is provided. I'll ask for forgiveness in advance - my CAD in Fusion 360 isn't very organized and is spur of the moment.

Tags