Starfish Pencil Holder — Organic Desk Star for 6 Pencils, Hollow Shell, Prints Without Supports
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A starfish lying on your desk, with six holes for pencils.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 1
- Makes
- 0
- Views
- 16
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Office
- License
- Creative Commons — Attribution
A starfish lying on the desk, holding your pencils.
The five arm holes lean outward 8 degrees, so the pencils fan out instead of standing in a bunch. The middle hole is dead vertical, for a marker, a pair of scissors or a brush. The pencils drop straight through and rest on the desk, held at two points — the hole and the table — so they stay put without needing a tube or a floor inside.
One continuous surface, no edges
This is not five arms glued to a middle blob. It was not built by adding solids together at all — it is a signed distance field, and the arms merge into each other with a tangent fillet. There is not one sharp edge anywhere on it. That is why it reads as an animal rather than as five cylinders.
Zero supports, and that is measured, not hoped
Overhangs under 45 degrees: 0.00 cm2
Watertight: 1 piece, 0 open edges
Size: 100 x 105 x 38.5 mm
Holes: 6 x 8.6 mm, 31 mm deep, centre 12.0 mm
Wall: 2.0 mm
The trick is in one line of the generator: every ellipsoid has its equator at z=0. So the widest cross-section of the whole model is the first layer, and the surface only ever narrows going up. Nothing can overhang because nothing is ever wider than what is below it.
Hollow, and why that is worth it
It is a shell, open underneath — you can see the whole starfish silhouette from below.
Volume: 119.4 cm3 solid vs 26.0 cm3 hollow shell
Print time: 2x solid vs 1x hollow shell
Filament: 2x solid vs 1x hollow shell
Sliced both ways with identical settings: the shell comes out at half the time and half the filament, for the same object from the outside. Around 2 h 30 on a bed-slinger at 0.2 mm, but check your own slicer for the exact figure.
Deciding how to hollow it took a measurement that contradicted the obvious one. A slicer flags overhangs by angle, and by that measure capping the cavity looked better. It is the wrong test: a flat ceiling is 0 degrees from horizontal and counts as a terrible overhang, but it is a bridge and prints fine. What actually matters is how much material lands on nothing, layer by layer:
Open to the top: 6.10 cm2 total over air, 0.61 cm2 worst single layer
Capped at z=30: 18.90 cm2 total over air, 9.32 cm2 at once worst single layer
So it is left open, and the dome closes gradually over five layers of about half a square centimetre each — which is what any hollow object does when it closes its roof. The angle-based test said the opposite.
Fair warning: those five layers leave the inside a bit stringy. You will never see it, but it is there.
Print settings
No supports. No brim. Nothing on this part needs either.
0.2 mm layers, 3 walls, PLA. The shell prints as walls, so infill barely matters — 0-10 %.
About 2 h 30.
Any colour works, but a warm orange or coral is the obvious one.
Two versions, and a generator
Starfish-Pencil-Holder-5-arms.stl: 5 + 1 centre = 6 pencils
Starfish-Pencil-Holder-6-arms.stl: 6 + 1 centre = 7 pencils
starfish_generator.py is the model. Every dimension is a command-line flag:
python3 starfish_generator.py --brazos 7 --lapiz 9.5
python3 starfish_generator.py --inclina 14 --centro 0
python3 starfish_generator.py --pared 0 — solid, if you prefer
--brazos: default 5 — number of arms
--lapiz: default 8.6 — hole diameter, mm
--r-agujero: default 22 — how far out the holes sit
--centro: default 12 — centre hole, 0 for none
--inclina: default 8 — degrees the arm holes lean out
--pared: default 2.0 — shell thickness, 0 = solid
--tapa: default 0 — cap the cavity at this height (see above — leave it)
--paso: default 0.6 — mesh resolution, mm
--reducir: default 0 — mesh decimation, 0.72 keeps 28% of triangles
Needs Python with numpy, scikit-image and scipy. It is not OpenSCAD: the shape is a distance field meshed with marching cubes, which is why the surface is continuous everywhere.
verify_starfish.py checks any result: one piece, watertight, overhang area, hole diameters and depths, and the layer-by-layer over-air test described above.
One thing to watch if you remix it
The lean on the holes is anchored at the mouth, not at mid-height. Anchor it in the middle and the hole drifts outward as it rises — straight into where the dome is thinning — and the wall drops to 1.02 mm. Anchored at the mouth it drifts inward on the way down, into solid material, and the wall stays at 2.63 mm. Same lean on the pencil either way; only the axis moves. Measured on the mesh, not guessed.