1 / 5
Sawstop CTS dust collection hood ( 2.5in dust collection port ) — image 1
1 / 5

Sawstop CTS dust collection hood ( 2.5in dust collection port )

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a dust collector that is over the saw blade of sawstop CTS. It utilizes the OEM riving knife for saw guard.

Rating
0 / 5
Likes
4
Downloads
11
Makes
0
Views
100
Reviews
0

Updated at source:

Model information

Category
Tools
License
Creative Commons — Attribution — Noncommercial — Share Alike

While sawstop CTS is a good saw in a lot of category, the dust collection on sawstop CTS is not so great... 

So I made a dust collection hood that uses the taller riving knife to mount on top of the saw blade. Hook a 2.5in dust collection tube to it, this helps cut down most of the sawdust that shoots toward you when you are ripping lumber. 

This is still the initial version, should still have many room for improvement. 

====== Material required ======

  • The taller riving knife that is meant for the saw guard

  • Thicker plexi-glass - I use 1.9mm ones and they were adequate for the job

  • m3-20mm bolt & nut x 1 

  • m4-20mm bolt & nut x 1

  • m5-20mm bolt & nut x 1

  • m5-30mm bolt x 2 

  • #8 x 1/2" truss head screw x 10 - similar to this pack from home depot 

  • small extension spring x 2  - I use the 3x16" by 1 3/4" spring from this harborfrieight spring pack

======= Steps to assemble ======

  1. remove the small metal tube that pokes out from the riving knife body. I use a dremel for this, but you should be able to just use any suitable tool to remove it as those tubes have very thin walls

  2. print the adapter piece. The best print orientation will be to have the short side on the printbed, so you can have the groove facing up. 

  3. Follow the adapter install graph to install the spring, the m3 m4 m5 20mm nuts and bolts. Use locking nuts if available.  
    At the end of the install you should have a adapter plate with m4 and m5 nuts fixed in the holes near the 2 ends, and a m3 nuts in the slots, connected to the m4 bolt with 2 extension spring and is able to slide in the short slots toward the m5 nut. 
    The reason of using bolt of 3 sizes... m5 is the right size for rear bolt, but is too large for the front bolt, but if I use m3 as the front bolt it creates too much play. And m3 is about the right size for the small indent in the t slot - it is possible to use m4 for that, but in my attempt it does not hold as well as m3 bolt.  In the end m4 in front - m3 sliding - m5 in the back give me the best result in my test, both for smoothness of install and minimal play after installed. 

  4. With the adapter assembled, test fit onto the riving knife by inserting the m5 nut vertically into the middle t shaped hole, then rotate the adapter downward toward the front. The M4 nut should be able to sanp into the hook in the front of the riving knife securely. 

  5. Next print the body part. The best print orientation is to have the split end on the print bed, so the 2.5in tube adapter is facing down. This will require at least 250mm space in Z axis, but will require the least support. Use brim to ensure a good bed adhesion.  Print with thick walls and higher infill to handle the screw thread and the sliding slot enlargemenet. I use 3mm wall ( 0.6mm nozzle x 5 wall count ) and 35% infill ( gyroid ) and it works well enough.

  6. Slide the body into the adapter, and you should be able to screw or even slide the 2 m5x30 bolt into the 2 secure pin hole to get a test fit.

  7. Carefully cut 2 strips of plexiglass to about 59mm in width with your table saw, line up the bottom edge of plexiglass to the bottom edge of the body piece, and use a small drill bit ( I use 3/32" ) to drill 5 pilot holes on plexiglass for the 5 mounting hole on body. ( I use a small clamp to secure the plexy glass to body, and put drill bit through the mounting hole and then through the plexiglass )

  8. use a bit that is larger than your truss screw's diameter to enlarge the mounting hole on plexiglass ( I use 5/32" bit ). 
    You want to ensure the hole is slightly larger than the screw, else the plexiglass will crack when you tighten the oversized screw to the body. 

  9. Use a 3/16" bit to drill through the pin slot location on the plexiglass - then wiggle it around the pin slot so that it opens the hole up further, to the point that the m5 bolt can slide inside that slot without too much friction. Do this on both plexiglasses. 

  10. Line up the body and plexiglass, use a few screw to secure position, then draw the cut lines so you can trim out the excess portion of the plexiglass.

  11. Use table saw to trim out the excess portion

  12. Secure the trimmed plexiglass to the body. The bottom of the plexiglass should be flush to the body. The 2 pin slots should have enough play for the m5 bolt to slide up and down without much difficulty. These slots are designed so that the hood have some vertical play, so we can avoid pinching the wood board being cut. 

  13. Final assembly - install the riving knife to the saw, slide the adapter plate onto the riving knife, and install the body onto the adapter plate the secure with the 2x m5x30 bolt

  14. Put a few layer of tape on the 2.5" hose adapter on body - the adaptor is intentionally made slightly smaller so we can use tape to create a friction fit that was just right.  If you have wide vinyl tape that may be the best for this task, but any tape would do. 

  15. install the hose, turn on dust collector and run some test cut. If everything works out correctly you should have very little dust on your table now. 

Tags