1 / 7
DeskPi RackMate TL1 top cover with 140mm fan mount — image 1
1 / 7

DeskPi RackMate TL1 top cover with 140mm fan mount

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Two piece top cover for the DeskPi RackMate TL1 10 inch rack. Takes a 140mm fan, no drilling needed.

Rating
0 / 5
Likes
1
Downloads
24
Makes
0
Views
126
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — Noncommercial — Share Alike

The TL1 ships with an open top. Anything warm in the rack dumps its heat straight up into the room, and dust drops straight back in. This is a cover for that opening with a mount for a 140mm fan.

I could not find anything made for the TL1. There is a decent amount out there for the T0, T1 and TT, but the TL1 has a different top plate so none of it lines up. I measured everything from the official TL1 STEP file and built this to match.

What it does

The cover drops into the 224 x 224 mm opening in the top plate and bolts down using eight of the holes that are already in the rack. No drilling, no modification.

By default the fan hangs underneath so the top surface stays flat and clean. If you would rather sit the fan on top, there is a setting in the SCAD file that flips it and adds a shallow recess for the fan frame.

There is a printed grille over the fan opening and a band of hex vents around it so air has somewhere to come in.

Printing

The cover is split into two halves with dovetails so it fits on a normal printer.

Front half: 232 x 133 mm

Rear half: 232 x 124 mm

Both are 8.6 mm tall

You need roughly a 240 x 140 mm bed. If you have a 256 mm or larger printer you can do it in one piece instead, set part to "whole" in the SCAD file and export that.

Settings:

0.2 mm layers

3 walls

15 percent infill

No supports, everything sits flat on the bed

PLA is fine for most setups. Use PETG or ASA if your rack runs warm.

Hardware

1x 140mm fan with the usual 124.5 mm screw spacing

4x M4 countersunk screws for the fan, 30 mm long for a 25 mm thick fan

8x M4 countersunk screws, 12 mm, plus 8 M4 nuts

The holes in the rack are 4.5 mm clearance holes and are not threaded, so you do need nuts underneath.

Assembly

1. Push the two halves together. The dovetails only go one way.

2. Sit the cover in the opening. The lip on the underside locates it.

3. Bolt the fan to the underside. Those four screws pass through both halves and clamp the joint, so do not skip them.

4. Fit the eight M4 screws and nuts around the edge.

5. Check the fan direction before you put everything back. Most people want it pulling air out of the rack.

If the lip feels tight in the opening, bump lip_clear in the SCAD file up by 0.1 or 0.2 and reprint. The anodised finish varies a little.

TL1 measurements

Posting these in case anyone else wants to design for this rack. All taken from the TL1 STEP file.

Top plate: 270 x 270 mm, 4 mm thick

Opening: 224 x 224 mm, centred

Fixing hole rows: 118.26 mm either side of centre

Hole positions along each row, either side of centre: 0, 15.875, 28.575, 44.45,

60.325, 73.025, 88.9, 104.775 mm

Holes are 4.5 mm

Nothing on the rack sits above the top plate, so it is a flat surface to work from

Editing it

The OpenSCAD source is included. The things most people will want to change:

fan_spacing, if your fan is not the standard 124.5 mm

fan_below, set to false to put the fan on top instead

hex_vent, set to false for a plain surface

screw_x, to use different holes in the rack

It renders in under a minute on OpenSCAD 2021.01.

Credits

Rack dimensions measured from the TL1 reference STEP file on Printables, which saved me a lot of time with a ruler. The rack in the renders is a rough model I built just to show how the cover sits. It is not included and it is not accurate enough to print.

Tags