Pin centre shifted for 9mm 26T 1.5GT toothed idler pulley
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
The central axis of the toothed idler pulley is shifted very slightly to account for the diameter difference.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 20
- Makes
- 0
- Views
- 231
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- GNU General Public License v2.0
The central axis of the toothed idler is shifted by 0.583mm in both X and Y directions to account for the difference in diameter between the Prusa smooth idlers and a 26T 1.5GT toothed one. This should allow the belts to run more parallel.
Pitch diameter line for toothed belt on smooth roller (Prusa design):
Smooth idler diameter = 12mm
Tooth height = 0.56mm
Pitch line offset = 0.23mm (the line where reinforcement fibres run in the belt)
Pitch diameter = 12 + ((2*(0.56+0.23)) = 13.58mm
Radius = 6.79mm
Pitch diameter line for toothed belt on 26T 1.5GT idler:
Pitch diameter = (1.5 * 26)/π = 12.414mm
Radius = 6.207mm
Distance to move pin centre = 6.79 - 6.207 = 0.583mm
EDIT: The calculation above is not correct (see below for a revised version). Eventually I may update this model but I'm including the calculations mostly for @DET-Man as I hope he will pull this small tweak into the main Pins Mod project.
Additional Details:
At first I struggled to find official documentation for 1.5GT belts as they don't seem to be part of Gates' main catalogue. Apparently 1.5GT is for special precision applications and is produced by Gates Unitta Asia. This led me to the following documentation:
https://www.unitta.co.jp/data/support/pdf/dendo_cat_b02_2024/dendo_cat_b02_15_092_112.pdf
...which includes this diagram:

PLD (Pitch Line Differential) is the offset between the pitch line (where reinforcement fibres are) and the flat part between the teeth on the belt.
We can also find the other dimension (let's call it PLB, for Pitch Line to Back) from the smooth back of the belt to the pitch line:
PLB = belt_thickness - tooth_height - PLD
For 1.5GT belts PLB = 0.21 mm
For 2GT belts PLB = 0.376 mm
The Gates Light Power and Precision Drive Design Manual includes the following:

Where Sprocket Pitch Circle circumference is the number of teeth * tooth pitch.
I.e. 26T * 1.5 mm = 39 mm
The radius of the Sprocket Pitch Circle is then: teeth * pitch / 2 * π
I.e. 26T * 1.5 mm / 2 * π = 6.207 mm (diameter = 12.414 mm)
Assuming that Prusa designed the Core One in a sane way, the baseline position of the XY carriage idler (relative to the edge of the belt tensioner pulley and the face of the XY carriage) should be:

The sum of...
Smooth Idler radius: R = 6mm
2GT Belt thickness: T = 1.38 mm
I.e. 7.38 mm for both X and Y offsets.
In my previous calculation I didn't take into account the difference in thickness between 2GT and 1.5GT belts. Using the 26T 1.5GT idler as an example we should position the pin centre as follows:

We add PLB to the Sprocket Pitch Circle radius to find the new X Y centre for the 26T idler:
For 26T 1.5GT idler:
PLB = 0.21 mm
26T Sprocket Pitch Circle radius:
26T_R = 6.207 mm
Offset for both X and Y:
PLB + 26T_R = 6.417 mm
By subtracting this offset from the 2GT and 12 mm smooth idler case we find how far the pin centre must shift:
26T Pin Centre Offset:
7.38 mm - 6.417 mm = 0.963 mm
For 21T 1.5GT idler (not advised):
PLB = 0.21 mm
21T Sprocket Pitch Circle radius:
21T_R = 5.013 mm
Offset for both X and Y:
PLB + 21T_R = 5.223 mm
21T Pin Centre Offset:
7.38 mm - 5.223 mm = 2.157 mm