Classroom Desk Name Plate — slide-in letter tiles, one alphabet sheet spells the whole class
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Name plate whose name is not in the STL: one dovetail track, one tile per letter, one sheet per class.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 9
- Makes
- 0
- Views
- 74
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Office
- License
- Creative Commons — Attribution
Classroom Desk Name Plate - The Name Slides In
Every printable name plate bakes the name into the mesh, so a class of 25 children is 25 STLs to slice, and the day the seating plan changes it is 25 more. This one keeps the name OUT of the plate. The plate is a tray walled on three sides with one dovetail track down the middle; the fourth side is open and that is the only way in. Every letter is its own tile and threads in from that open end. Print ONE alphabet sheet for the whole class, one plate per desk, and spell each name by hand in about ten seconds. It lies flat or stands up as a "^" tent.
131 x 42 x 13 mm plate, 7 slots, ~12.6 mm capitals. 41 tiles: A-Z plus the fifteen Czech accented capitals. Blanks pad the row so a short name sits centred. A split-foot end stop presses in last and locks the row. The walls stand exactly as tall as a seated tile, so nothing can be knocked out sideways or lifted over the wall.
WHAT TO PRINT plate.stl 1 piece 56 g - the plate. name.stl 7 pieces 24 g - EMMA + blanks + end stop. alphabet.stl 41 pieces 142 g - the whole alphabet, once per class. blanks.stl 6 pieces. stops.stl 4 pieces. stand.stl 2 pieces 29 g - both tent brackets. back_panel.stl 1 piece 35 g. letters.zip - every letter on its own: 41 plain files plus 41 two-colour twins. name_2c.stl - the name sheet as two named solids for an AMS. Two prints make one finished plate. No screws, no glue.
PRINTING PLA or PETG, 0.20 mm layers, 3 walls, 15% infill, NO SUPPORTS, NO BRIM. Both dovetail flanks are drawn at exactly 45 degrees; measured on the meshes, every sheet file carries 0.00 mm2 of unsupported overhang. DO NOT FLIP THE TILES - they are exported widest-face-down, and upside down the dovetail foot becomes the overhang.
Assembly - 3 Minutes, No Tools
Deburr the mouth of the track with a fingernail if the first layer left a lip. 2. Work out the row: the name plus blanks for the remaining slots. 3. Feed the tiles in through the OPEN RIGHT END in reading order, leftmost character first; each slides the length of the track and stops against the one before it, on light thumb pressure. 4. Push the END STOP in last - its split foot squeezes on the way in and holds the row against the closed end. To re-spell, pull the stop out with a fingernail and slide the row back out. 5. To stand it up, press one bracket onto each end and slide the back panel down into the second groove of both. Print a second plate instead of the back panel for a name on each side.
TWO COLOURS Plate one colour, tiles another - zero purge, because the tiles are a separate print, not a filament change. For coloured letters: every glyph on every tile starts at exactly Z = 8.20 mm, so ONE filament change there colours a whole sheet for ~0.35 g. Or use the AMS files: name_2c.stl splits into tile_bodies + letters, and the archive holds an <X>_2c.stl per letter that splits into exactly two parts. Accented capitals included - the caron is tied to its letter under the skin. Turn IRONING OFF on the tile tops.
MAKE YOUR OWN - THE SOURCE IS ATTACHED The .scad is the exact parametric source and is written to be edited. A different name is one variable: openscad -o zoe.stl -D 'part="name"' -D 'name="ZOE"' classroom_name_plate.scad - the blank count is derived, so the row always fills the track and the name ends up centred, and a name too long fails with a message. Accented characters do not survive the command line; edit the name = line in the file. A letter the sheet has not got goes in extra_glyphs (and in extra_accented if it carries a loose accent) - anything the font can draw works, and it gets its own tile on the alphabet sheet plus its own letter_i index. A different-sized plate has three knobs: n_slots (how many tiles fit - the plate length follows, never a fraction of a slot), plate_depth (the across-the-desk dimension in mm, 0 = derived) and size (one master scale for the letters and everything derived from them: pitch, cap height, plate, rim, stand). size 0.7 gives 92 x 29 mm, size 1.5 gives 196 x 63 mm. Clearances stay ABSOLUTE - a 0.2 mm dovetail fit is a print tolerance, not a proportion. Re-export the plate and the tiles together: tiles from one setting do not fit a plate from another. Default typeface is Arial Narrow Bold; PT Sans Narrow Bold is a free substitute.
