Zusammenklappbares Regal und Skadis-Lochwand Display
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Das ist ein Regal mit 4 Schubladen zum Auseinander ziehen. Zusätzlich ist eine Skadis Lochwand Auf der Ersten Kiste.
- Rating
- 0 / 5
- Likes
- 17
- Downloads
- 16
- Makes
- 0
- Views
- 161
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Organizers
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Das ist ein Regal mit 4 Schubladen zum Auseinander ziehen. Es kann für MakeUp verwendet werden. Aber natürlich für alles was man zum Hobby an klein teilen rumliegen hat. An die Skadiswand kann allerlei befestigt werden. Die Löcher der Skadiswand sind erweitert worden, so das man diese besser nutzen kann. Wäre toll wenn Ikea das mit ihrer Lochwand ebenfalls umsetzt.
Zusätzlich ist eine Skadis Lochwand auf der Ersten Kiste. Die Kisten werden mit Stegen verbunden. Die Stege sind auf der Innenseite mit Nummern gekennzeichnet. Die Kennzeichnung muss beim zusammenbauen immer nach innen/oben zeigen. Ich habe zu den Stegen(Position) ein Bild dazu Hochgeladen. Die Kisten sind hinten ebenfalls Nummeriert. Untere Kiste ist die Nummer 4, von da nach oben. Die Obere Kiste hat die Nummer 1. Die Einsatzkisten sind mit links, rechts, Mitte benannt, die Deckel dafür ebenfalls. Von den Kiste-Trenner kannst Du so viele machen wie Du benötigst.
Zum Montieren der Stege benötigt:
Drucken von 20 Stiften.
Drucken von 20 Stiftscheiben.
Zum Verschrauben: 20 Inbuss Senkschrauben M3x6 oder M3x8.
Messing Einschmelzgewinde M3. Ich haben Ruthex genommen. Diese werden in die Stifte eingesetzt.
Für die Rückwand: 4 Inbuss M4x16 und 4 Messing Einschmelzgewinde M4.
Ich habe mit Infill von 25% gedruckt. Außer die Stege die sind mit 35% Infill gedruckt.
Die Kisten haben eine breite von 210mm.
Die gesamtbreite ist 240mm.
Die Höhe mit der Skadis Lochwand ist 385mm.
Falls das Regal Zustimmung findet, werde ich noch eines für einen kleineren 3D Drucker Hochladen(220x220mm).
This is a unit featuring four pull-out drawers. It can be used for makeup or, of course, for storing any small hobby-related parts you might have lying around. A Skadis pegboard can be attached to the unit; the holes on the pegboard have been enlarged to make them more usable—it would be great if IKEA adopted this design for their own pegboards.Additionally, a Skadis pegboard is mounted on top of the uppermost box. The boxes are connected by struts, which are numbered on the inside. When assembling, ensure these markings face inward or upward. I have uploaded an image showing the strut positions. The boxes are also numbered at the back, starting with number 4 at the bottom and counting up to number 1 at the top. The insert trays are labeled "left," "right," and "center," as are their lids. You can print as many box dividers as you need.
To assemble the struts, you will need:
20 printed pins.
20 printed washers.
Fasteners: 20 M3x6 or M3x8 countersunk hex screws.
M3 brass heat-set inserts (I used Ruthex brand); these are inserted into the pins.
For the back panel: 4 M4x16 hex screws and 4 M4 brass heat-set inserts.
I printed the parts with 25% infill, except for the struts, which were printed with 35% infill.
The boxes are 210mm wide.
The total width is 240mm.
The total height, including the Skadis pegboard, is 385mm.
If this design proves popular, I will upload a version for smaller 3D printers (220x220mm).