1 / 13
Prusa XL Toolhead Nozzle Brush, Wiper & Debris Collector by LLH — image 1
1 / 13

Prusa XL Toolhead Nozzle Brush, Wiper & Debris Collector by LLH

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Prusa XL værktøjshoved dysebørste, dysevisker og snavsboks fra LLH

Rating
0 / 5
Likes
2
Downloads
12
Makes
0
Views
175
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

🇬🇧 English

Prusa XL Toolhead Nozzle Brush, Wiper & Debris Collector by LLH

I designed my own nozzle cleaning system for the Prusa XL, which cleans the nozzle as each toolhead moves in and out of its dock.

The wiper can be adjusted both side-to-side and up/down, making it possible to precisely align the wiper with the nozzle.

At each toolhead dock there is a silicone nozzle wiper and a removable debris collector, which catches filament residue removed from the nozzle.

Adjustable mounting

The mounting bracket is attached to the Prusa XL frame and can be adjusted vertically as well as sideways.

This makes it easy to position the silicone wiper precisely in relation to each nozzle.

No rattling from the debris collector

To prevent the removable collector from rattling, I made two small Ø1.75 mm holes in the adjustable mounting bracket.

For these I use Spectrum S-Flex 90A filament directly from the spool.

I cut two pieces of filament, press them into the holes from the side and trim them at the edges.

The S-Flex protrudes only approximately 0.10 mm from the contact surface.

That tiny amount is enough for the collector to sit firmly against the flexible contact points.

The result is a debris collector that sits firmly without play or resonance noise, while still being easy to remove when it needs to be emptied.

It works perfectly.

Nozzle cleaning at all 5 toolheads

With all five installed, the nozzle is cleaned whenever a toolhead moves in and out of its dock – and therefore also during tool changes.

Removed filament residue falls directly into the corresponding debris collector instead of falling around inside the printer.

The collector can simply be removed, emptied and clicked back into place without disturbing the adjustment of the wiper.

Together with the new Prusa bed wiper
https://www.printables.com/model/1814173-xl-printable-parts

At the same time, I use Prusa's new Prusa bed wiper/nozzle cleaner.

Here, the nozzle moves back and forth as well as in and out across the cleaning area, cleaning the nozzle tip thoroughly from several directions during filament changes.

When cleaning is finished, the nozzle moves over the small metal part in front of the cleaning area, where the printer finds/references the Z-zero height using the clean nozzle tip.

So now I have nozzle cleaning both at the tool docks and with Prusa's new bed wiper.

For me, this combination makes a lot of sense on a multi-tool Prusa XL: clean nozzles and the removed filament collected in removable boxes instead of around the printer.

Parts needed – per wiper/collector

For a 5-tool Prusa XL, multiply the quantities above by 5.

Print settings

  • Material: PETG

  • Layer height: 0.20 mm

  • Infill: 15%

  • Supports: Yes – SNUG supports

Best regards
Leif Lumby Henriksen
Odense3D Community: https://facebook.com/groups/2911561982402973


🇩🇰 Dansk

Prusa XL værktøjshoved dysebørste, dysevisker og snavsboks fra LLH

Jeg har tegnet min egen nozzle-renser til Prusa XL, som renser dysen, når et toolhead kører ind og ud af sin dock.

Wiperen kan justeres både sidelæns og op/ned, så den kan tilpasses præcist til dysens placering.

Ved hver toolhead-plads sidder der en silicone nozzle wiper og en aftagelig opsamlerboks, som samler filamentresterne op.

Justerbar montering

Beslaget monteres på Prusa XL-rammen og kan justeres både op/ned og sidelæns.

Det gør det muligt at placere silicone-wiperen præcist i forhold til dysen på hvert toolhead.

Ingen raslen fra opsamlerboksen

For at undgå, at den aftagelige opsamlerboks sidder og rasler, har jeg lavet to små Ø1,75 mm huller i det justerbare beslag.

Her bruger jeg Spectrum S-Flex 90A filament direkte fra filamentrullen.

Jeg klipper to stykker filament, presser dem ind i hullerne fra siden og skærer dem af ved kanterne.

S-Flex'en stikker kun ca. 0,10 mm ud fra kontaktfladen.

Det ganske lille fremspring er nok til, at opsamlerboksen sidder fast mod de fleksible kontaktpunkter.

Resultatet er, at boksen sidder fast uden slør eller resonanslyde, men stadig nemt kan tages af, når den skal tømmes.

Det virker perfekt.

Rensning ved alle 5 toolheads

Når alle fem er monteret, bliver dysen renset, når et toolhead kører ind og ud af sin dock – og dermed også ved toolskift.

Filamentresterne falder direkte ned i den tilhørende opsamlerboks i stedet for at ende rundt omkring i printeren.

Opsamlerboksen kan nemt tages af, tømmes og klikkes på igen, uden at man ændrer justeringen af selve wiperen.

Sammen med Prusas nye bed wiper
https://www.printables.com/model/1814173-xl-printable-parts

Samtidig bruger jeg Prusas nye Prusa bed wiper/nozzle cleaner.

Her bevæger dysen sig frem og tilbage samt ind og ud over rensefeltet, så dysespidsen bliver renset grundigt fra flere retninger ved filamentskift.

Når rensningen er færdig, flytter dysen hen over den lille metaldel foran rensefeltet, hvor printeren finder/refererer 0-højden med den rene dysespids.

Så nu har jeg rensning både ved tool-docks og med Prusas nye bed wiper.

For mig giver kombinationen rigtig god mening på en Prusa XL med flere toolheads: rene dyser og filamentresterne samlet i aftagelige opsamlere i stedet for rundt omkring i printeren.

Nødvendige dele – pr. wiper/opsamler

Til en Prusa XL med 5 toolheads skal ovenstående antal ganges med 5.

Printindstillinger

  • Materiale: PETG

  • Laghøjde: 0,20 mm

  • Infill: 15%

  • Support: Ja – SNUG support

Med venlig hilsen
Leif Lumby Henriksen
Odense3D Community: https://facebook.com/groups/2911561982402973

Tags