Sentinels of the Multiverse - Villain Card Holder
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A folding card holder for "Sentinels of the Multiverse" Villain cards. Fits 130mm cards.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 2
- Makes
- 0
- Views
- 31
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Board Games
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a contraption that I designed for use with the "Sentinels of the Multiverse" card game - It holds the Villain cards upright so they're visible to the table, and makes flipping the cards easier. The parts separate, and the legs fold down under the base, for easy storage. Additionally, there are magnets embedded in the parts so that the rotation stops at 180 degrees.
The Villain cards are 130mm wide (unsleeved), so this holder would be compatible with any other games that use 130mm cards.
If you try this out, let me know how it works and please share any feedback.
Additional Materials:
[Optional] 1/8" x 1/16" disk magnets (4x per holder). I used these: https://www.magcraft.com/magcraft-nsn0566. These are optional, and are just used to stop the rotation at 180 degrees.
Glue (CA/superglue, or your preferred glue).
Print Settings:
For reference, I printed these using Prusament PLA, on a MK3S machine. I printed the parts using the "0.2mm QUALITY" setting in PrusaSlicer, with 15% infill. With these settings, printing all the parts in one go takes about 5 hours, and about 47g of filament (~16m)
The only place the print settings may really matter is with the "MagnetCover" part - It's sized for 0.2mm layer heights.
The parts are designed so Supports are not needed, but there are a few bridges, so enable Supports if needed.
Some of the parts benefited from Brims, to help ensure print success. I'll call these out below.
Print Instructions:
Some Villains will have two Villain cards, so consider printing two copies.
Specific instructions, or things to watch for, are called out for each part below.
BaseAndLegs:
When loading the BaseAndLegs part into the slicer, you may be prompted about a "multi-part object". Select the option to load the file as a single object with multiple parts.
Make sure that the first layer includes all three legs and the main body:

The parts should all be aligned already, but this is good to double-check. The print is likely to fail otherwise.
CardHolder:
There are two variations of the CardHolder part, one for Sleeved cards, and one for Unsleeved cards - Choose the appropriate one for your case.
For reference, the Villain cards are listed as 130mm wide on BGG (here), and the sleeves I tested with were about 133mm wide. The holders are sized based on these measurements, with a bit of wiggle room.

Enable a Brim for this model.
CenterPost:
I recommend enabling both the Inner and Outer Brim. This helps ensure that the small cutouts for the magnets stay aligned properly while the first layers print.
MagnetCover:
This is an optional part - I use this to cover the magnets in the Base.
This part is 0.4mm tall, so it would slice best at 0.2mm layer height.
Assembly Instructions:
Once the parts are printed, remove any Brims, and check the fits:
The CenterPost should fit into the corresponding registration cutout in the CardHolder. It will not be a snug/tight fit.
The legs should freely rotate, and fold under the base. You may need to move them manually once or twice first.
If using magnets, follow the steps immediately below. Otherwise, jump to "Part Assembly" further below.
Magnet Installation:
These steps are only required if using the magnets.
The important part of this assembly is to make sure all the magnets are installed in the same/correct orientation, so the rotation works. It may help to also mark the faces on the magnets to remember the orientation.
First, glue the magnets in the CenterPost. I found it easier to do these one at a time and let the glue fully dry in between each; Otherwise, the magnets tended to jump out of the parts before the glue dries enough. Double-check that the magnets are in the same orientation, and allow the glue to fully dry.
Next will be installing the magnets in the Base. To make this easier, we'll use the CenterPost magnets:
Put one additional magnet on each one already installed in the CenterPost.
Apply glue to the two holes in the Base where the magnets will go.
Inset the CenterPost into the hole in the Base. Twist until you feel the magnets settle into their slots.
While still pushing down, twist the CenterPost 90 degrees, and then remove. Wipe any residual glue off the CenterPost.
This method reliably left the magnets in the Base, and ensured they were in the correct orientation.
Once all of the glue is dried, move onto "Part Assembly".
Part Assembly:
Whether or not you use the magnets, you can add the optional MagnetCover: Apply a bit of glue at the bottom of the shaft cutout in the Base, and drop the MagnetCover in. This part is purely aesthetic.
Before gluing the CenterPost into the CardHolder, check the fit - Depending on how the parts finish, you may need to sand one or the other a bit to get them to mate properly.
Apply glue to the mating surfaces of both parts, and press the CenterPost into the registration cutout in the CardHolder. I used a clamp to hold the parts while the glue dries.