1 / 30
1/4 Scale Federal Signal 500-SHTT/A/AT — image 1
1 / 30

1/4 Scale Federal Signal 500-SHTT/A/AT

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Fully functional and customizable model of the later generation Federal Signal 500-SHTT, 500-A, and 500-AT!

Rating
5 / 5
Likes
23
Downloads
57
Makes
2
Views
424
Reviews
2

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

(Ignore the table of contents, Printables adds it if your text has headers and I don't know how to get rid of it😭)

(This video is WITH THE SUPERCAPACITOR SETUP) (Huge thanks to Jack (Jev9911) for testing out the supercap setup for me!!!

OVERVIEW:

Ever since I brought the concept of using a dual shaft TT gearmotor as a gearbox for a siren to life with my Penetrators/Allertors, I always knew I wanted to make a 500 with that same concept! In fact, the 500's rotator is even more accurate with this setup considering the real siren also uses an extra belt and pulleys to connect the back motor shaft to the gearbox! The only downside to the rotator design of this 500 is the fact that is that the "clutch" is the same design as my Penetrators/Allertors. It's a press-fit gear which means if it's rotated way too much and abused, it will eventually wear out and need to be re-printed or glued.

Although the siren itself is quite complex, I've poured a LOT of time into making all the assembly steps very straight foreword while also not having any stupid design choices or ideas. The only thing that can be tricky is getting the order of the way things go together correct, but the images in the instructions should help a lot with the process!

Like many other sirens, the 500s have differences and it's important to understand what 500 you actually want to make so you know what parts you need to print and what instructions you need to follow! 

This image is everything you need to understand before starting the project:

PARTS LIST:

MOTOR: https://www.amazon.com/CHANCS-Electric-555-8000RPM-Accessory/dp/B0CW61NGF4/ref

SHAFT COUPLER(S): https://www.amazon.com/12Pcs-3-17mm-Coupling-Connector-Airplane/dp/B0DKT5T64L/ref

ALAN WRENCH:

Any LONG 1.5mm alan wrench will work but the ones that come with the coupler are not long enough. Here's one you can use although feel free to search for another one or style you prefer!

https://www.amazon.com/Dynamite-DYN2814-Hex-Driver-1-5mm/dp/B000BQ1SFE/ref

SLIP RING: https://www.amazon.com/Comidox-CIRCUITSx2A-Capsule-Electrical-Equipment/dp/B07H2SRMXP/ref

THRUST BEARING: https://www.amazon.com/FOCMKEAS-AXK3047-Bearings-Thickness-Industry/dp/B0CY5NSXR9/ref (There are a couple other listings for the thrust bearing you'll need. If you want to look for another, make sure it has a 30mm ID, 47mm OD, and a 4mm thickness!

GEARBOX: https://www.amazon.com/SparkFun-Hobby-Gearmotor-140-Pair/dp/B07JX7MHSL/ref

OR: https://www.amazon.com/Pack-Dual-Shaft-Gear-Motor/dp/B0C448W34R/ref

M3 THREADED INSERTS: https://www.amazon.com/dp/B08BCRZZS3?ref

M2 THREADED INSERTS: https://www.amazon.com/ruthex-Threaded-Insert-pieces-ultrasound/dp/B088QJG676/ref

M3 HARDWARE KIT: https://www.amazon.com/Machine-Assorted-Assortment-Stainless-Threaded/dp/B0DFWYBJJJ/

M2 HARDWARE KIT: https://www.amazon.com/Machine-Assorted-Stainless-Assortment-Threaded/dp/B0DFWXRM21/ref

CASSETT TAPE BELTS: https://www.amazon.com/Recorder-Cassette-Maintenance-Machine-Repeater/dp/B0CZ4549WN/ref


POWER:

BUCK CONVERTER: https://www.amazon.com/dp/B0DFH46JPD?ref=ppx_yo2ov_dt_b_fed_asin_title

SUPER CAPACITORS: https://www.amazon.com/dp/B0DBQYF49G?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

This is my first siren to officially use supercapacitors to achieve a lengthy wind-up and a wind-down even close to a minute!!! 

To wire the supercapacitors, you want to wire them in a series (not parallel!) This diagram shows you how to wire it:

Since the siren is quite big and there's a lot of space inside, you can do a lot of setups. For example, you can solder the supercapacitors directly to the motor terminals, glue them somewhere else in the motor cover, or even put them in the rotator box bottom!

A few things that are really important, you can NOT use a PWM speed controller with supercapacitors!!! You NEED either a power supply or a buck converter (the ones I used are linked!!). Another thing to note is that the voltage coming out of the buck converter has to be wired correctly to the supercapacitors. POLARITY MATTERS!!! Wire the positive coming from the buck to the positive on the supercaps and same with the negative. 

And one of the most IMPORTANT THINGS is that you NEED to use a voltage meter to test how much is coming out of your buck before you wire it to the supercaps. The supercaps (when wired in a series) have a max voltage or around 10 volts. If your buck converter is putting MORE than 10 volts out, there is a chance your supercaps will go kaboom!! So make sure you turn the voltage to around ~7.5, then connect the supercaps, then wire it to the siren and tune it to the perfect pitch! The siren shouldn't even need very close to 10 volts to run properly.


INSTRUCTIONS: 

(Instructions BY DEFAULT are for the SHTT, separate/different steps for the 500A/500AT will be at the bottom!)

(Like pretty much every other siren) Start by printing the rotor. It will have a center hole for the shaft coupler to fit in. It should be toleranced to need a hammer to tap itself in but if yours is pretty loose, put a small line of super glue inside the hole (on either side OPPOSITE of the setscrew holes as to not get glue inside) And speaking of the setscrew hole(s), make sure they're aligned with the small holes inside of the rotor otherwise your rotor AND shaft coupler are junk.

 (Photo is from my 1/3 scale Model 2/Thunderbolt rotor but it's the same concept)

If you want to test out the rotor on your motor, refrain from tightening the setscrews a LOT as stressing out the threads and setscrews can give your rotor wobble. Wait to crank it all the way down once you have the stator on there too!

And speaking of the stator, that's the next thing you'll print. The SHTT's stator is a two-piece stator where the outer horn ring and the stator floor are two separate pieces. Start by bolting the motor to the stator floor piece (disk piece) and make sure that the motor is going INTO the indent! Now bolt your motor cover onto the back (also with four M3 inserts in the front).

I'd also take the time now to add all the rest of the inserts onto the stator floor before you put the horn ring on. You can still do it but it's a lot easier to get it done now, it takes two M2 inserts in the little side nubs and two more M3s in the two close-together holes also located on the back for the eyebolt bracket (My version of the stator floor in the image above didn't have the two insert holes for the eyebolt bracket but yours will!) Now that you've completed your stator floor, go ahead and take your horn ring piece and slot the stator floor into the back of the horn ring. The pieces are toleranced to have a slight gap and the nubs that fit in their corresponding slots keep the motor/motor cover horizontal.

(This is how they should fit together. My version also didn't use M2 inserts in the side nubs but yours will have them! Also keep in mind the alignment of the horn ring on the front side! There's 5 M2 insert holes for the intake and you want to MAKE SURE that the orientation of it has one hole almost directly in the top middle of the stator as opposed to two evenly spaced out)

Now, before you weld the two pieces together, you'll actually want to put the rotor onto the motor shaft and tighten it down (not too much yet) so that you can align the stator to your need. Make sure the rotor is in the correct position and the two stator pieces are completely meshed inside eachother. Once you have it in the right position (shouldn't take a while) you can go ahead and weld all around the back of the two pieces to fuse them together! If you don't have any scraping and you think you're alignment is good, you can go ahead and crank those setscrews down! Now is also a great time to test the core if you wan to hear how it sounds!

For the rotator, start by printing the main rotator frame as well as the outer rotator tube. You'll need to sand the tubes until they slide inside of eachother very smoothly. You can also set the thrust bearing into the little groove in the bottom frame as you do this to test out your tubes as you're sanding. Once you've gotten them nice and smooth, print the bottom rotator plate. You'll notice it has a circular hole with a groove right in the center for the outer rotator tube to slide in and sit flush inside. Put a lot of super glue into that groove and press in the outer rotator tube. You'll also want to plastic weld all around the top to essentially fuse the two pieces together.

Instead of explaining how to assemble the rotator step by step (totally not a reference to the song I used in said video), I decided to record a video goes over the whole rotator assembly process to help with any possible confusion!

Now, to attach the whole core assembly onto the rotator, you'll first need to understand a big issue with the 500 itself. The horn is not able to be taken off of the stator UNLESS the entire motor/core assembly is removed from the rotator base due to the fact that the horn bolts on from the back. Yes, I know it's an insanely STUPID design choice but BLAME FEDERAL!!!! It's like that on the real 500s too and I'm just trying to make mine accurate. THEREFORE... If you'd like to test out the core, you can go ahead and due so since it really isn't all that much work to tighten down the four bolts that hold on the core. However unless you have the horn on already, I would NOT recommend soldering the wires from the slip ring to the motor UNTIL you have the completed core assembly with the horn bolted to the back!

Anyways, with all that aside we can talk about the horn itself. It's split up into two or four sections (depending on how big your printer is) and also includes a back ring piece. You'll want to get all the horn sections printed and plastic welded together. Once the horn is complete, drop the back ring into the INSIDE of the horn, center it out, and plastic weld that to the horn as well. To attach the horn to the core, secure it with six M3 bolts onto the 6 M3 inserts on the back of the stator. Now if you'd like, you can attach the core/horn assembly to the rotator and solder the wires! 

The whole rest of the siren assembly is very simple. I didn't go over the bottom stand assembly BUT in the rotator assembly tutorial video right at the beginning, I show pretty much how the whole thing bolts together so you can watch that if you're confused.

The intake attaches onto the front of the stator with five M2 inserts and the outer intake cone piece should nicely press onto the intake and also secure to the front of the intake with five M2 screws with nuts on the ends. 

Those two close-together inserts on the back of the stator right above the motor are for the eyebolt bracket. It simply screws into those two inserts with M3 screws and is where you can thread an eyebolt. An eyebolt isn't linked, but you can go to a hardware store and find some small screw eyebolts that should work perfectly! If you need to widen the top hole because your eyebolt is too big, you can also drill it out a bit. Just make sure you don't drill out too much since you still want a decent thread!

The back cover is self explanatory, secures with six M2 screws that go into inserts on the back, and those two M2 inserts on the side-nubs on the stator floor piece. 

The rotator frame side panels all attach with M2 hardware and inserts and for the junction box, push it through the hole on the corresponding panel for it. The cover uses M2 screws that simply plastic thread to hold on.

 And that's all for the SHTT!!! 

500-A/500-AT INSTRUCTIONS

With the entire rotator and bottom frame setup and some other things here and there being the exact same as the SHTT, I will not be going over any parts that are repeated. You will likely still need to read most of the SHTT's instructions and especially the rotator assembly video to understand certain steps! 

CORE ASSEMBLY:

The core of the 500A/AT is also a two piece stator, but in a different way. The whole thing goes together like a sandwich with the motor on the back, stator floor on top, stator on top of that, and the two horn connection ring pieces on top of that. The motor attaches to the stator floor with two M3 bolts while the motor cover AND outer stator are attached by four more. DO NOT bolt the motor cover onto the back of the stator floor UNLESS you also have the outer stator on as well. It all goes together in one piece! Before you do this, note that the two bottom most holes on the stator floor are for M3 inserts. Sink those inserts in before you assemble the pieces!

(Arrows are where inserts go, make sure they also go IN the direction of the arrows!)

(This is how it should look. The four arrows are where long M3s go through the inner stator, stator floor, and finally into the M3 inserts in the motor cover. Also keep in mind the orientation of the stator floor relative to the motor cover. The flat side is facing downwards)

From here, you'll need to attach the horn connection ring halves. Those attach with one M3 bolt (with a nut on the end) as well as one insert (the two you previously sunk in to the stator floor bottom). This is how they go on:

(This is a piece I myself have not tested yet and I don't know for sure if the two bolts on each ring are enough to hold the thin pieces flat against the stator, let alone the horn weight pulling on them. Please let me know (if you do print this) if it is able to handle the weight or if it needs a redesign!)

Okay, with that ALL out of the way, all that's left is to slide the rotor on and tighten the setscrews! If you'd like to test the core, now would be a good time!

Now if you recall, I said that Federal fixed the issue of the horn not being easy to take off when they designed the A and AT. That's true HOWEVER, due to the scale of this mini, two of the M2 screws needed to secure the horn on are insanely hard to access due to how close the bottom rotator plate comes to where the screws come out (this image)

So... You have two options here. You can either build the entire horn assembly and attach it to the core assembly with ALL of the M2s that go around the back horn ring. OR you can attach the core to the rotator assembly and bolt all the ones that you can access (what I'd do)

For the long rotator, the only difference is the longer motor cover, longer back cover, and also a gap plate you'll find in the rotator folder. Locate the two small holes at the very front of the bottom rotator plate on either side. Those are for M2 inserts that you can use to bolt the gap plate onto the rotator with (see image below)

You'll also notice that there's a big hole in the back of the motor cover with a smaller circular hole in it. That's for a single M3 insert in order to attach the eyebolt bracket. It should go together like this:

The motor pulley is also longer to bridge the gap between the two motor shafts.


And that's it for the 500A/AT!!

Tags