1 / 5
PLAYMOBIL Steck Castle Walkway Floor / Wehrgang 3007615 (30076150) - 3666 Replacement Part — image 1
1 / 5

PLAYMOBIL Steck Castle Walkway Floor / Wehrgang 3007615 (30076150) - 3666 Replacement Part

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

3D-printable replacement for PLAYMOBIL part 3007615 / 30076150, the 1-wide rectangular castle walkway floor / Wehrgang

Rating
0 / 5
Likes
2
Downloads
13
Makes
0
Views
40
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

This is a 3D-printable replacement for PLAYMOBIL part 3007615 / 30076150, the 1-wide rectangular castle walkway floor / Wehrgang used in the classic PLAYMOBIL Steck construction system.

The original part can be found in classic medieval castle sets including PLAYMOBIL 3665, 3666 and 3667, as well as other constructions using the same Steck castle system.

I tried to reproduce the original part as closely as possible, including the plank-style floor surface, the two curved upright supports and the surrounding mounting and connection geometry.

The model is intended as a replacement for missing or damaged original walkway sections while retaining the appearance and construction style of the original PLAYMOBIL castle system.

Because printer calibration and material shrinkage can vary slightly, minor cleanup of connection areas may occasionally be required.

RECOMMENDED 3MF FILE

I recommend using the supplied 3MF file rather than simply importing the model and applying a standard slicer preset.

The supplied project contains the intended printing orientation together with two manually positioned support regions underneath the areas that actually require support.

This keeps support material concentrated around the difficult underside features instead of generating unnecessary supports across the rest of the part.

The exact printing parameters are provided separately in the Settings and manufacturing instructions.

3D printing settings

RECOMMENDED PRINT SETUP

The supplied 3MF is optimized for:

  • Printer: Bambu Lab A1

  • Nozzle: 0.4 mm

  • Layer height: 0.08 mm

  • Initial layer height: 0.20 mm

  • Material: PLA

  • Wall generator: Classic

  • Walls: 3

  • Infill: 12%

  • Infill pattern: Gyroid

  • Top layers: 8

  • Bottom layers: 6

  • Slicer resolution: 0.005 mm

  • Scale: 100%

  • Build plate: Textured PEI

The supplied orientation should be kept as-is.

The model uses 12% Gyroid infill throughout the main part, providing a good balance between strength and filament consumption.


SUPPORTS

The project uses manually controlled Normal supports rather than relying on automatic support generation across the complete model.

Support configuration:

  • Supports: Enabled

  • Type: Normal (Manual)

  • Style: Snug

  • Threshold angle: 30°

  • Top Z distance: 0.16 mm

  • Bottom Z distance: 0.16 mm

  • XY distance: 0.45 mm

  • Top interface layers: 2

  • Bottom interface layers: 0

  • Interface spacing: 0.30 mm

  • Base-pattern spacing: 2.5 mm

  • Support expansion: 0.6 mm

  • Build-plate-only: On

  • Support speed: 40 mm/s

  • Support interface speed: 25 mm/s

MANUAL SUPPORT ENFORCERS

The supplied 3MF contains two dedicated support-enforcer volumes:

SUPPORT ENFORCER - LEFT UNDERSIDE STRIP

and

SUPPORT ENFORCER - RIGHT UNDERSIDE STRIP

These modifiers force support specifically underneath the two difficult underside strips while leaving the rest of the model free from unnecessary support material.

This is intentional and is one of the main reasons I recommend using the supplied 3MF.

Do not delete either support enforcer.

Because the project uses Manual supports, removing the enforcers can result in these areas printing without the intended support.


PRINTING ORIENTATION

Keep the orientation supplied in the 3MF.

The walkway floor is positioned horizontally while the two curved supports rise vertically from the main floor section.

This orientation keeps the large plank-style surface in a practical printing position while allowing the two localized underside areas to be handled by the manual support enforcers.

Do not use Auto Orient unless you intend to develop a different support strategy.


BUILD-PLATE ADHESION

The active project currently uses:

  • Brim: None

  • Brim width: 0 mm

No additional brim is required by the supplied configuration.

If your particular filament or build plate has poor adhesion, a brim can still be added manually, but it is not part of the supplied optimized project.


PRINT SPEEDS

The supplied project uses:

  • Outer wall: 40 mm/s

  • Inner wall: 70 mm/s

  • Sparse infill: 90 mm/s

  • Internal solid infill: 70 mm/s

  • Top surface: 40 mm/s

  • First layer: 50 mm/s

  • Support: 40 mm/s

  • Support interface: 25 mm/s

The more visible outer walls and top surfaces are printed more conservatively while the internal structure is allowed to print faster.


LINE WIDTHS

The project uses:

  • Outer wall: 0.42 mm

  • Inner wall: 0.45 mm

  • Sparse infill: 0.45 mm

  • Internal solid infill: 0.42 mm

  • Top surface: 0.42 mm

  • Initial layer: 0.50 mm

  • Support: 0.42 mm


MATERIAL

The supplied project is configured for PLA.

Saved filament profiles include:

  • Bambu PLA Matte

  • Bambu PLA Basic

Typical saved starting temperatures are:

  • First-layer nozzle: 220°C

  • Nozzle: 220°C

  • Textured PEI bed: 65°C

  • First-layer bed: 65°C

  • Cooling fan: approximately 60–80%

These values can be adjusted if necessary for your particular PLA.


WHY USE THE SUPPLIED 3MF?

The supplied project preserves the intended:

  • Printing orientation

  • 0.08 mm high-detail layer height

  • 3-wall construction

  • 12% Gyroid infill

  • 0.005 mm slicer resolution

  • Two manually positioned underside support enforcers

  • Tuned Snug support clearances

  • Build-plate-only support strategy

  • Part-specific print speeds

Simply importing the model and selecting a standard preset will not reproduce the two manually positioned support regions.

For the intended balance of print quality, strength, low filament usage and easy support removal, use the supplied 3MF as the starting point.

Tags