1 / 7
SPEY HARD SH-003 Fly rod HANDLE & FIGHTING BUTT 9' #7 — TPU foam, 3D printed — image 1
1 / 7

SPEY HARD SH-003 Fly rod HANDLE & FIGHTING BUTT 9' #7 — TPU foam, 3D printed

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A custom 3D-printed TPU-foam handle and matching fighting butt.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
38
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

A custom 9ft #7 single-hand fly rod build, paired with a 3D-printed TPU-foam handle and matching fighting butt. Built to take the abuse of travel fishing. The photos show the actual finished rod — both parts were printed on a regular FDM printer and glued on. Not renders or prototypes.

This release includes the two custom 3D-printed parts of the build. The blank, guides, reel seat, and consumables are off-the-shelf and listed in the BOM below.

## What's in this release

- SH-003-handle.stl — custom design, mixed half-/full-wells style handle

- SH-003-butt.stl — small (~2 cm) fighting butt

Both parts print upright on a standard FDM printer with direct drive. Supports used for handle. The TPU filament foams during printing — no post-processing is needed.

## What you'll need (BOM, not in the STLs)

- Blank: Aventik Saltwater IM10 9FT LW7 — 4-piece, 2 tips, metallic blue

- Reel seat: NooNRoo Aluminum Reel Seat 16# (light grey)

- Guides: NooNRoo Fly Rod Guide Set, silver

- 1× tip-top

- 8× snake guides (running)

- 2× stripping guides

- Guide positions (cm from tip-top): measured for this specific blank; re-space for other blanks

0, 11.9, 24.1, 38.5, 55.3, 73.8, 91.8, 113.4, 136.3, 163.6, 193.0

- Wrap thread: Prowrap Nylon, color 449 "wild blueberry"

- Decorative trim: 300D Rod DIY Guide Fasten Metal Line No. 14

- Finish: Hilevel Rod building finish (over thread wraps)

- Glue for handle & butt: Flex Coat Rod Builders' Epoxy Glue

- Glue for reel seat: LOCTITE Power Epoxy Extra Time 60min

- Personalization: self-made vinyl labels (e.g. "SPEY HARD 7# 9ft SH-003")

## Print settings — handle

- Layer height: 0.20 mm

- Walls: 4

- Nozzle: 0.4 mm

- Nozzle temp: 250 °C

- Fan speed: 0%

- Infill: 19% honeycomb

- Fuzzy skin: ridged_multifractal, starting at 39.45 mm (same height where the denim grip section begins)

- Bed temp: OFF

- Print orientation: upright

- Layer zones (filament changes):

- 0 – 39.45 mm: eSun TPU-LW (black)

- 39.45 – 155 mm: Recreus Filaflex Foamy 95A (denim)

- 155 mm – end: eSun TPU-LW (black)

## Print settings — fighting butt

- Same as handle, with adjusted layer zones:

- 0 – 11.05 mm: eSun TPU-LW (black)

- 11.05 mm – end: Recreus Filaflex Foamy 95A (denim)

## Notes

- Handle and butt bore is 11 mm as printed

- Recommended minimum build volume: ~200 mm Z-height (handle is 166 mm high and prints upright)

- Direct-drive extruder strongly recommended for TPU

- The foam surface on the printed parts is the final grip texture — no sanding, no coating needed, but a light sanding pass gives a slightly softer feel

## Tip: if your blank's butt is thicker, you can enlarge the bore by placing a cylinder hole in Tinkercad on the imported STL

## Build guide

Wondering what it takes to build a rod from parts? The whole process — from finding the spine to wrapping and finishing — is documented on my blog: https://en.blog.speyhard.fi/

Tags