1 / 3
Beseler 45 Negative Carrier – 6 x 12 Horseman (112 Mask) — image 1
1 / 3

Beseler 45 Negative Carrier – 6 x 12 Horseman (112 Mask)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Hinged, one-piece printable Beseler 45 negative carrier for 6x12 panoramics on 120/220 from a Horseman back (112 mask).

Rating
0 / 5
Likes
1
Downloads
2
Makes
0
Views
10
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

⚠ Please Read the Instructions First

These carriers work like the original Beseler carriers, but they are plastic, not metal, and plastic has to be handled differently. The included PDF walks through printing and assembly step by step. Following it is the surest way to a carrier that works the way it should.

Printable replacement negative carrier for Beseler 45-series enlargers, for 6x12 Horseman (112 mask) negatives.

Why three versions? The Horseman 6x12 mask is marked 112mm, but measured negatives from different backs run 112, 113 and 114mm. Measure a developed frame from your own back. Choose the matching carrier for a clean full-frame print, or go one size up if you want a thin black border showing the edge of the negative.

Hinged, One-Piece Carrier

Works like the original Beseler carriers. The top plate is joined to the bottom by a print-in-place hinge, so it opens, loads and closes exactly like the OEM part. This is not a two-piece sandwich you have to assemble before it goes into the enlarger. Original Beseler 45 carriers locate with pins; the later 23C carriers use a locating ring. This carrier uses a ring sized for the 45 so both series share one parametric design. The difference is in form only: it seats and centers the carrier in the stage exactly as the pins do.

Only additional items needed: CA (super) glue and a hammer.

Not for Commercial Use

This model is licensed under Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0): http://creativecommons.org/licenses/by-nc-sa/4.0/ Print it for yourself, for friends, or for your camera club. Selling prints or files, whether on eBay, Etsy, print-on-demand services or anywhere else, requires a commercial license. Contact me to arrange one.

Specifications

  • Enlarger: Fits all Beseler 45-series enlargers (45M, 45MX, 45MCRX, 45MX-II, 45MXT, 45V-XL and variants).

  • Film: 120/220 roll film

  • Used with: Horseman 6x12 roll film backs, including on the Horseman SW612

Print Settings

  • 0.08 mm layer height, 0.4 mm nozzle

  • PLA, opaque matte black recommended (pins may be a light color)

  • Print on the smoothest plate you have; avoid textured plates

  • Do NOT use any XY hole compensation; the pin holes are an interference fit

  • Top and bottom usually need separate plates

Files

  • Negative_Carrier_Beseler_45_6_x_12_Horseman_112_Mask_Bambu.3mf (Bambu Studio)

  • Negative_Carrier_Beseler_45_6_x_12_Horseman_112_Mask_Generic.3mf (other slicers, tested in PrusaSlicer)

  • Negative_Carrier_Beseler_45_6_x_12_Horseman_112_Mask_top.stl (top plate with print-in-place hinge)

  • Negative_Carrier_Beseler_45_6_x_12_Horseman_112_Mask_bottom.stl (bottom plate)

  • NegativeCarrier_Aligment_Pins_Undercut_All.stl (4 pins per carrier)

  • Beseler_23C_45_Negative_Carrier_Printing_And_Assembly_Instructions.pdf

Assembly

Full steps are in the included PDF: drive the 4 undercut pins, break the print-in-place hinge free, then glue the hinge to the bottom plate with CA glue.

Support This Work

Every carrier here is free and always will be. If one has earned a place in your darkroom and you'd like to say thanks, the tip jar is here: https://www.printables.com/@jschwefel_1261537/collections/3772975 Thank-you plaques at f/5.6 ($5), f/8 ($8) and f/11 ($11).

Tags