50 cents penetration
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A 3D-printed coin illusion: coins apparently pass through a solid card, one after another, in full view.
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 12
- Makes
- 0
- Views
- 248
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Toys & Games
- License
- Standard Digital File License

INTRODUCTION
I have modified this classic coin magic principle so that it can be 3D printed. This trick uses two cylinders, a plastic card and a few coins. Coins apparently pass through a solid plastic card, one after another. The effect can be performed with the objects in full view, and everything can be examined before and after the performance.
The complete construction and handling are explained in the accompanying video.
PRINTING INSTRUCTIONS
Material: PLA or PETG (PETG preferred for durability)
Layer height: 0.20 mm
Nozzle: 0.4 or 0.6 mm
Infill: 60% or more recommended
Supports: Needed for the inside of the sliding parts only
Print orientation: Print the cylinders as provided, with the four “legs” facing up. Do not print the other parts vertically. They need perfectly circular holes to fit the cylinders, which makes vertical printing unsuitable.
Brim: Use if necessary for your printer.
Number of printed parts: 5 (2 cylinders, Slate A, Slate B and the plastic card)
Remove the supports from the inside of the sliding parts carefully. Do not remove too much material around the cylinders or inside the holes, as a small amount of friction is required in several places.
A standard poker-size playing card can also be used instead of the 3D-printed plastic card.
THE PRINCIPLE
The principle is based on a very precise internal ledge inside the cylinders. When several coins are placed inside the two-part cylinder with a card in the middle, the geometry allows one coin to remain secretly trapped while the others can fall.
The tolerance is deliberately very precise. A small change in position or vibration can cause the trapped coin to fall, which is used to create the appearance of the penetrations. For this reason, five similar coins are required, even though only four coins are openly seen during most of the routine.
PREPARATION & ASSEMBLY

After printing, you will have five pieces:
- Two identical cylinders, a plastic card, and the two other sliding parts
The cylinders are designed to be assembled with the sliding parts. When assembled, the sliding parts should have a small amount of friction to keep them together.
I designed these parts to be glued, but during testing I realized that if the fit is good, you can perform the trick without glue. If the parts become too loose after repeated use, they can be glued.
When gluing, do not allow glue to enter the internal ledge of the cylinder, as this could make the principle less precise. After assembly, make sure that the cylinders are perfectly flat.
For better visual contrast, I recommend using a different colour for the card.
SETUP
You will need:
The assembled cylinders
The plastic card
Five similar coins
Try to use coins with a similar appearance. Ideally, they should have a similar level of wear, so that one coin cannot easily be distinguished from another.
PERFORMANCE
Begin by showing the pieces and allowing the spectator to examine them. Assemble the two cylinders to make one long cylinder. Place a coin inside the cylinder and show that it moves freely through it.
Insert the card between the two parts of the cylinder and show that the coin can no longer pass through.
Place four extra coins without explicitly showing how many you are adding, and try to conceal the thickness of the stack slightly while adding them. Turn the cylinder upside down, and four coins will fall out.
Turn the cylinder upside down again, but keep it slightly tilted to prevent the secret coin from falling.
Drop the four coins into the cylinder. The hidden coin should then fall. Turn the cylinder upside down to show that only three coins remain in the upper part.
Repeat these moves three more times.
The accompanying video is strongly recommended, as the exact positioning, timing and handling are much easier to understand visually.
TIPS & IDEAS
The exact timing and handling are demonstrated in the accompanying video, along with a few additional phases and the final cleanup, allowing you to hand everything back for examination.
LICENSE — NON-COMMERCIAL USE ONLY
This design is provided for personal and non-commercial use only.
You may:
* Download and print the design for your personal use.
* Use the printed object for your own personal use.
* Share photos or videos of your creations, provided that Mathieu Bich is credited and the original Printables page is linked.
You may not:
* Sell or redistribute the STL files.
* Upload or share the STL files on other platforms.
* Sell the printed objects.
* Use the design or printed parts for commercial purposes.
* Modify and redistribute the design or modified STL files.
* Use the design for print-on-demand or manufacturing services.
Commercial use requires prior written permission from Mathieu Bich.
SUPPORT MY WORK
If you enjoy my magic and would like to support my work, you can support me on Patreon (nothing on it yet but soon ;-)
ABOUT THE CREATOR
Created by Mathieu Bich, professional magician and creative consultant.
If you are looking for a magician for an event, or for creative consulting and magic design for a project, you can discover my professional work here:
Or simply search for Mathieu Bich on YouTube and discover magicians from around the world performing magic I have created.