1 / 1
Kedarnath — image 1

Kedarnath

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A 3d model of Kedarnath mountain with track and watershed using https://mapsto3d.com/

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
24
Reviews
0

Updated at source:

Model information

Category
Test Models
License
Creative Commons — Public Domain

# How to turn any place on Earth into a 3D printable map

A complete guide to going from a flat map to a printed relief model, in a browser, for free.

---

## Why print a map at all

A map on a screen is a picture of a place. A map you can pick up is something else. Run a thumb along a ridge line and you understand the valley in a way no contour shading ever quite delivers. Hand someone the town they grew up in and watch them find their own street without being told where to look.

Printed relief maps used to mean vacuum-formed plastic from a school supplier, or a CNC router and a block of tooling board. They don't any more. The elevation data is public, the map data is public, and a browser can do the geometry. This guide walks through the whole thing, including the parts that usually go wrong the first time.

Everything below is done with [MapsTo3D](https://mapsto3d.com) — free, no account, no watermark, no export limit, and it runs entirely in your browser so nothing is uploaded anywhere. But most of the advice here is about relief maps in general and applies whatever you use to make them.

---

## What you need

- A browser. That's genuinely it.

- A printer. FDM is fine. Resin is fine too and gives sharper contour lines.

- About twenty minutes for your first one.

No account, no install, no CAD.

---

## Step 1: Pick the place — and pick the right size

This is the step everyone gets wrong, so it goes first.

The instinct is to grab a whole mountain range. Resist it. The interesting thing about a relief map is the relief, and relief is a ratio. Take a 200 km wide slab of the Himalaya and print it 150 mm across and the 8,000 m of mountain becomes 6 mm of gentle bumpiness. Take an 8 km wide piece of the same range and the same mountain stands 60 mm tall.

Good first areas:

| Area width | What it suits |

|---|---|

| 2–5 km | A town, a city centre, a single peak, a lake |

| 5–15 km | A valley, a mountain and its approaches, a bay |

| 15–50 km | An island, a whole massif, a metropolitan area |

| 50 km + | A region — expect gentle relief, lean on colour and contours instead |

Search for a place, drag the frame where you want it, and pick a shape. Square reads as a classic wall map. Round makes a coaster or a paperweight. Hexagons tile together if you want to build a region a piece at a time. You can also rotate the frame to any angle, which matters more than it sounds — aligning the frame to a valley rather than to north often makes a far better object.

---

## Step 2: Get the vertical exaggeration right

Here is the arithmetic that decides whether your print looks like a mountain or a biscuit:

relief on the print (mm) = (height range in m / area width in m) x print width (mm) x exaggeration

Worked example. Everest, an 8 km square, printed 150 mm wide. The height range in that box is about 3,200 m.

(3200 / 8000) x 150 x 1 = 60 mm of relief at 1x — dramatic, no exaggeration needed

Now the Norfolk Broads, a 10 km square with 25 m of range, printed 150 mm wide:

(25 / 10000) x 150 x 1 = 0.4 mm — invisible

(25 / 10000) x 150 x 15 = 5.6 mm — now it reads

Rules of thumb:

- Real mountains (1,500 m+ of range): use 1x. They are already dramatic. Exaggerating them makes spiky nonsense that prints badly and looks fake.

- Hills and coastlines (100–1,500 m): 1.5x to 3x.

- Lowlands, river deltas, cities (under 100 m): 5x to 20x. Yes, really.

MapsTo3D has an automatic setting that reads the height range and picks a sensible number, and it tells you what it chose. Start there, then nudge. Trust your eye over the formula — the formula tells you the ballpark, your eye tells you when it is right.

---

## Step 3: Decide what the surface says

A bare terrain mesh is a shape. A map is a shape that tells you things. There are broadly three routes:

Colour the surface with imagery. Satellite, topographic, or street basemap draped over the terrain. Best for single-colour prints where you will paint afterwards, or for GLB/OBJ exports into Blender where the texture does the work. It looks superb on screen and does nothing at all for a monochrome print.

Paint the ground with land cover. Woodland, grass, farmland, wetland, sand, rock, ice and built-up areas, each as its own colour part, taken from OpenStreetMap. This is the single biggest upgrade for a flat area. A plain terrain plate of somewhere in the Netherlands is a blank rectangle; the same plate with farmland, water and built-up areas picked out in three filaments is a real map.

Raise features off the surface. Buildings at their real heights, roads, railways, rivers, your own GPX track. A city centre with extruded buildings is the classic, and it is the one people ask for.

They stack. You can have land-cover colour and raised buildings and contour lines on the same model.

---

## Step 4: The two details that make it read as a map

Inlaid water. Printing water as a flat pad on top of the ground is the obvious approach and it always looks wrong — rivers sit proud like plastic worms. Water should be cut into the ground, so the lake surface sits below the bank and the river runs in a channel you can feel with a fingernail. Then, if you are printing in colour, the blue fills a recess instead of perching on a surface. Same data, completely different object.

Contour lines. Raised lines at a fixed height interval, exactly as a paper topographic map draws them. They do two things: they make the terrain legible at a glance, and they give a monochrome print something to catch the light on. A single-filament grey model with contour lines has more presence than a flat one in three colours.

Choose the interval in real metres, so it means what a map reader expects. For a mountain, 100 m or 200 m. For hills, 20 m or 50 m. For lowland, 5 m or 10 m. If you set it to automatic, the interval gets picked from the height range and told to you.

Keep lines at least 0.8 mm wide if you want them to print cleanly on FDM — that is two perimeters at a 0.4 mm nozzle. Thinner works on resin.

---

## Step 5: Base thickness

The base is not decoration. It is what stops a wide thin plate curling off the bed.

- 3–4 mm for anything up to about 150 mm across.

- 5–6 mm above that, or for anything you will handle a lot.

- Add another millimetre or two if you plan to carve water into the surface, so the channel does not cut through to daylight.

A deeper base also gives you a clean side wall to emboss a place name into, which is worth doing — a relief map without a label is a nice object, and a relief map with "SOLUKHUMBU, NEPAL · 27.99°N 86.93°E" along the front edge is a gift.

---

## Step 6: Bigger than the bed

Every printer has a limit and every good map idea is bigger than it. Split the model into tiles.

Two ways to think about it:

1. By grid — "3 columns by 2 rows", when you know the arrangement you want on the wall.

2. By tile size — "no piece bigger than 200 mm", when you know your bed and want the software to work out the grid.

The second is usually what you want. Set your printer from the list (A1 mini, P1S/X1C, H2D, MK4, Mini, Ender 3, K1 Max, Saturn) and it will keep every piece inside the build volume.

A few things that save grief:

- Print one tile first. Check the height, the line width, the colour changes. Then commit to the other eleven.

- Add a frame. A raised border around each tile hides the seam, gives the pieces a defined edge, and makes a multi-tile map look deliberate rather than broken.

- Number the underside. You will not remember which corner piece is which.

---

## Step 7: Export

| Format | Use it for |

|---|---|

| 3MF | Multi-colour printing. Every layer is a separate part with its own material, so Bambu Studio, PrusaSlicer, OrcaSlicer and Cura open it already assigned. This is the one you want for an AMS or MMU. |

| STL | Single colour. One file, everything merged, works everywhere. |

| STL zip | One STL per colour. Load them into any slicer and assign extruders yourself. The manual route to multi-colour, and the only route in some slicers. |

| GLB | Textured, for Blender, Unity, Unreal or a web viewer. |

| OBJ | Textured, classic, with material file and texture image. |

| DXF | 3D faces on named layers, for AutoCAD or Rhino. |

For printing, the honest answer is: 3MF if you have multi-material, STL if you do not.

---

## Slicer settings that actually matter

These are starting points for FDM, not commandments.

- Layer height 0.16–0.2 mm. Terrain is all gentle slopes, and slope is exactly where layer lines show. 0.12 mm is visibly better on a small model and doubles your print time.

- No supports. A relief map is a heightfield. Nothing overhangs. If your slicer wants supports, something is wrong — usually a water channel cut deeper than the base.

- 2–3 perimeters, 10–15% infill. The top surface is the whole point and it is fully supported by the walls; you do not need dense infill.

- Ironing on the top surface if your slicer has it, but only for flat-topped areas like sea level. On sloped terrain it does nothing.

- Slow down the top solid infill to around 30–40 mm/s. Terrain top surfaces are a huge fraction of the visible object.

- Cooling on, full. Fine contour lines and building edges need it.

- A brim on anything wider than 150 mm. Big flat plates curl.

Material: PLA is right for this. It is dimensionally stable, it is stiff enough for a thin wide plate, and it comes in the colours a map wants. PETG will do it but is more prone to stringing across the fine raised features. Matte PLA photographs far better than glossy — a matte grey terrain plate looks like a museum piece.

---

## Multi-colour without an AMS

You do not need a tool changer to print a two-colour map. Two tricks:

Filament swap at a layer. Print the base and terrain in one colour, insert a pause at the layer where the contour lines or land cover start, and swap. Works because most map features sit on top of the terrain at a consistent height. Every slicer has a colour-change-at-layer function.

Print the parts separately and glue. Export the per-colour STL zip, print the water in blue and the terrain in grey as separate flat pieces, and inlay them. More work, much sharper colour boundaries than any single-nozzle trick, and it is how the nicest maps get made.

---

## Five places worth printing first

Coordinates and a suggested starting size. All of these are chosen because they have enough relief to work at 1x or close to it.

1. Everest and the Khumbu — 27.988 N, 86.925 E, 8 km wide. About 3,200 m of range. Contours at 200 m. The obvious one, and it earns it.

2. The Grand Canyon — 36.10 N, 112.11 W, 28 km wide. Prints best round. Water inlaid so the Colorado reads as a cut, not a stripe.

3. Manhattan — 40.758 N, 73.986 W, 3 km wide. Buildings on, terrain almost flat, exaggeration irrelevant. This is a building print, not a terrain print.

4. The Matterhorn — 45.976 N, 7.659 E, 7 km wide. The best-shaped mountain on Earth for this, and it needs no exaggeration whatsoever.

5. Pangong Tso — 33.73 N, 78.75 E, 45 km wide. Long lake between high ridges. Inlaid water at this scale is genuinely striking.

---

## Licensing, briefly

The elevation comes from AWS Terrain Tiles, the map data from OpenStreetMap, the imagery from Esri, the basemap from OpenFreeMap and OpenMapTiles. Each keeps its own licence, and OpenStreetMap's in particular (ODbL) has requirements about attribution and about derived databases.

For printing a model for yourself or giving one to a friend, this is a non-issue. If you are selling printed maps or publishing the files, read the licences — and at minimum credit OpenStreetMap in the listing. It costs you one line and it is the whole deal those volunteers ask for.

---

## The tool

[MapsTo3D](https://mapsto3d.com) — free, no account, no watermark, no export limit.

It runs entirely in your browser. Location searches go to a map server the way any map site's would, but the model itself is built on your own machine and never uploaded. Square, round, hexagonal and free-drawn frames; land cover, inlaid water, contour lines, buildings at real heights, roads, rail, rivers and your own GPX tracks; printer presets and automatic tiling; STL, 3MF, per-colour STL zip, GLB, OBJ and DXF out.

If you print something with it, post it. I would genuinely like to see them.

Tags