1 / 8
Intex Ultra XTR Pool Cover sphere frame/ Unterkonstruktion Abdeckplane — image 1
1 / 8

Intex Ultra XTR Pool Cover sphere frame/ Unterkonstruktion Abdeckplane

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

spärische Unterkonstruktion für Poolabdeckfolie Spherical substructure for pool cover tarpaulin

Rating
0 / 5
Likes
3
Downloads
5
Makes
1
Views
120
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — NoDerivatives

Um das Regenwasser von der Plane ablaufen zu lassen, festfrieren der Poolabdeckung an der Wasseroberfläche zu verhindern und somit die Lebensdauer der Plane zu erhöhen, habe ich die Unterkonstruktion mit 20 mm Elektroinstallionsrohren konstruiert. Alles wird nur zusammengesteckt und kann im Sommer leicht verstaut werden. Die unteren Rahmenhalter werden auf die Poolecken aufgesteckt und mit einer M6x25 Inbusschraube und einer M6 Mutter gesichert.

Bis auf die Stangenclipse sind alle Teile ohne Supportmaterial druckbar, dazu sollten die Schichthöhen an problematischen Stellen auf das Minimum reduziert werden. Ich habe schon alle Teile so ausgerichtet, dass sie ohne Support gedruckt werden können. Auf Grund der Spannung im Rohr empfehle ich die slicer-Einstellung von min. 3 Perimeter, 8 Boden- und 5 Deckelschichten. Als Material empfehle ich ASA da sich die Poolplane im Herbst und Frühjahr doch sehr aufheizt.

Benötigt werden:

  • 16x untere Rahmenhalter links

  • 16x untere Rahmenhalter rechts

  • 4x T-Verbinder

  • 8x X-Verbinder

  • 8x Y-Verbinder

  • 1x Mittelkreuz

  • 1x Stützplatte

  • 1x Gegenplatte

  • 4x Schnurspanner

  • 64x Stangenclip DN20

  • 4x Stangencip DN25

  • 16x Inbusschraube M6x25

  • 16x Sechskantmutter M6

  • 19x 20 mm Installationsrohr (Längen: 16x 1990 mm (das dicke Ende wegschneiden), 16x 185 mm, 8x 517 mm)

  • 4x 25 mm Installationsrohr (Länge je nach Wasserstand)

  • optional 1x 25 mm Installationsrohr als mittelabstützung (Länge je nach Wasserstand)

  • 1x Styrodurplatte 1200x600x50

  • Schnur

Alle Mengen- und Längenangaben sind für einen 4,88 m Pool mit 16-segmentigem Rahmen

Wenn es euch gefällt vergesst bitte das Like nicht und lasst gern auch ein Make da.

Description

To allow rainwater to drain off the tarp, prevent the pool cover from freezing to the water’s surface, and thus extend the tarp’s lifespan, I built the substructure using 20 mm electrical conduit. Everything simply snaps together and can be easily stored away in the summer. The lower frame brackets are snapped onto the corners of the pool and secured with an M6x25 Allen screw and an M6 nut.

With the exception of the rod clips, all parts can be printed without support material; however, the layer heights should be reduced to a minimum in problematic areas. I’ve already oriented all the parts so they can be printed without supports. Due to the tension in the tube, I recommend a slicer setting of at least 3 perimeter layers, 8 bottom layers, and 5 top layers. I recommend using ASA as the material, since the pool cover gets quite hot in the fall and spring.

Required:

  • 16x lower frame holder left

  • 16x lower frame holder right

  • 4x T-connectors

  • 8x X-connectors

  • 8x Y-connectors

  • 1x star connector

  • 1x support plate

  • 1x counterplate

  • 4x cord tensioners

  • 64x rod clips DN20

  • 4x rod clips DN25

  • 16x M6x25 Allen screws

  • 16x M6 hex nuts

  • 19 x 20 mm installation pipe (lengths: 15 x 1990 mm (cut off the thick end), 15 x 185 mm, 5 x 517 mm)

  • 4 x 25 mm installation pipe (length depending on water level)

  • Optional: 1 x 25 mm installation pipe as a center support (length depending on water level)

  • 1x Styrodur panel 1200x600x50

  • Cord

If you like it, please don't forget to hit “Like,” and feel free to leave a “make” as well.

Tags