1 / 5
Armytrix Remote Case and Holder for Nissan 370z — image 1
1 / 5

Armytrix Remote Case and Holder for Nissan 370z

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Flex case for your Armytrix exhaust remote and Flex or Petg holder for Nissan 370z blank button replacement.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
21
Reviews
0

Updated at source:

Model information

Category
Automotive
License
Creative Commons — Attribution — Noncommercial — Share Alike

Models + Print Instructions

There are 3 groups of models you can use (folders named accordingly).

  1. PETG + FLEX Holder - files ends with "_flex" (Recommended)

    1. print the button with PETG
      (the button has slightly bigger hole for the flex holder)

    2. print the holder with FLEX
      - keep the position of the model and use preferably organic supports
      (the button accounts for that)

  2. PETG only Holder

    1. print the button with PETG
      (the button has slightly smaller hole for tighter fit of the petg holder)

    2. print the holder with PETG
      - keep the position of the model and use supports
      - the model has finger hole for you tu push the remote out of it
      - the case is not enclosing the remote fully, so you can push it in and out

  3. FLEX Case
    - print the case with FLEX (supports might not be needed)
    - you can use it as is OR
    - you can use it when creating your own holder (please share the final holder)

Installation

Installation is very simple

  1. grab the holder with your right hand
    (put the thumb into the hole, rest of the finger outside on right side)

  2. drag up strongly - you want to hear and feel simple "click"

  3. grab the cup holder on the left side
    (this time the fingers inside and thumb outside)

  4. again drag up - you wan to hear another "click" sound

  5. now the bottom part should go up easily - just push it up

  6. the last "click" comes from the front and the holder is all free

  7. remove the most left blank button
    (using flat screw driver to release two lock on both sides of blank button)
    - in my case this required quite a bit of strength

  8. install the holder from the top
    - just push the printed button inside the newly created hole

You can see the removal of the cup holder for example in this video.

Story

I have Armytrix exhaust installed on my 370z Nismo and this came with the Armytrix remote for the valves inside of the exhaust. For some time I've been driving with the remote inside of the cup holder, but it is not practical at all - you must reach for it if you want to quickly close the valves and you cannot use cup holder for nothing much else.

I came to conclusion that I need some more comfortable way to control my exhaust. I though about hardwiring the exhaust to some simple switch, or create custom case for it. Then it came to my mind - just use some phone holder and create some mount or holder for the remote.

At first I thought about using this one that I'm already using for my phone - just mirroring it and put at the driver's side. After some search I found this thing, which suits me even better.

So I've dived into creating the case for the remote, which was painful, as it has it's "diamond" shape and one side is not even straight. But after some time the case was ready, now how to put it onto the button?

During the development I've decided that I can use flex for the case, so the button sits there comfortably, won't fall out of the case and also is easily removable if needed. So I've borrowed the idea of circular joint (as I'm no fan of using glue).

Some tinkering here and there and it's done. The remote sits inside the flex case which is connected into the button and also lays on center console itself. Now I only thing about buying some red FLEX filament, to give it a little more glance.

Tags