Fiat Ducato / Moveo P600 – Reinforced Guard Rail Interior door
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Reinforced Guard Rail / Balconnet de porte Interior door
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 4
- Makes
- 0
- Views
- 37
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Noncommercial
Fiat Ducato / Moveo P600 – Reinforced Retaining Bar / Guard Rail
A reinforced replacement for the door retaining bar (handle) / retention bar (handle) found on the main door of the Moveo P600 motorhome, based on the Fiat Ducato.
The original part is quite thin and tends to break over time, especially when someone accidentally grabs it thinking it is a handle.
I designed this replacement to be significantly stronger than the original. The mounting section has also recently been slightly thickened for additional strength, while keeping the original screws, so no special hardware is required.
Print & durability
The first version was printed in PETG and has now been installed on my motorhome for approximately 3 years.
During this time, it has:
remained firmly in place
shown no deformation
not melted or softened
survived prolonged exposure to direct sunlight while the motorhome was parked outside
That said, if I were printing it today, I would probably use ASA, particularly for better long-term UV and outdoor resistance.
The Fusion 360 source file is included, allowing you to modify the part if necessary — for example, the curvature can be adjusted to better suit your door or installation.
⚠ Note: This is an independently designed replacement part and is not an original Fiat or Moveo component. Check the dimensions and fit before installation.
AI disclosure: This description was written with the help of AI, but the 3D model itself was designed 100% manually by me in Fusion 360.
---------------------------------------------------
Remplacement renforcé de la barrette de retenue (poignée) / barrette anti-chute/Balconnet de porte (poignée) de la porte principale d'un camping-car Moveo P600, basé sur le Fiat Ducato.
La pièce d'origine est assez fine et finit par casser avec le temps, notamment lorsqu'une personne s'y accroche par mégarde en pensant qu'il s'agit d'une véritable poignée.
J'ai donc conçu un modèle nettement plus solide que la pièce d'origine. La partie servant à la fixation a récemment été légèrement épaissie afin d'améliorer encore sa résistance, tout en conservant les vis d'origine : aucun matériel spécifique n'est nécessaire.
Impression et résistance dans le temps
La première version a été imprimée en PETG et est installée sur mon camping-car depuis maintenant environ 3 ans.
Durant cette période, elle :
est restée parfaitement en place ;
ne s'est pas déformée ;
n'a pas fondu ni ramolli ;
a résisté à une exposition prolongée au soleil lorsque le camping-car était stationné à l'extérieur.
Cela dit, si je devais la réimprimer aujourd'hui, je choisirais probablement de l'ASA, notamment pour sa meilleure résistance aux UV et aux conditions extérieures sur le long terme.
Le fichier source Fusion 360 est fourni, ce qui permet de modifier facilement la pièce si nécessaire, notamment la courbure de la barrette, afin de l'adapter au mieux à votre porte ou à votre installation.
⚠ Attention : il s'agit d'une pièce de remplacement conçue indépendamment et non d'une pièce d'origine Fiat ou Moveo. Vérifiez les dimensions et l'ajustement avant installation.
Transparence : cette description a été rédigée avec l'aide d'une IA, mais le modèle 3D lui-même a été conçu à 100 % manuellement par mes soins sur Fusion 360.