1 / 2
Soprano Rebec (remix of "Alto Rebec" by alleycat) — image 1
1 / 2

Soprano Rebec (remix of "Alto Rebec" by alleycat)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A smaller, higher-pitched remix of [Alto Rebec by alleycat](https://www.printables.com/model/460663-alto-rebec)

Rating
0 / 5
Likes
2
Downloads
4
Makes
0
Views
36
Reviews
0

Updated at source:

Model information

Category
Music
License
GNU General Public License v2.0

# Soprano Rebec (remix of "Alto Rebec" by alleycat)

A smaller, higher-pitched remix of [Alto Rebec by alleycat](https://www.printables.com/model/460663-alto-rebec)

(Printables, licensed GNU GPL v2.0). This remix keeps the original's bowl-body/dovetail-neck

architecture and banjo-tuner pegbox, scaled down to a ½-size-violin string length and tuned

a fifth higher.

## What changed from the alto

- Tuning: D-A-E (up a fifth from the alto's G-D-A) — the same three pitches as the top three

strings of a standard violin.

- Strings: ½-size violin strings (nominal ~285mm scale length), vs. the alto's ¾-size strings

(~308mm, measured from the original files).

- Scale factor: all acoustic/structural dimensions — body, soundplate, fingerboard, neck shaft,

nut, bridge, tailpiece, tailpiece nut — are scaled to 0.9237× the alto's geometry, referenced

from the nut position. That is roughly a 19% reduction in total print material/time.

- Pegbox left full-size: the pegbox paddle (the part with the three tuner holes) is not scaled

down. It's carried over from the alto unchanged, because it has to fit the same physical tuner

hardware (Ø10mm bore, Ø17mm barrel clearance, 3× banjo tuners, 4:1 ratio — same spec as the alto).

Only the neck shaft between the pegbox and the body is shortened/thinned. This mirrors how real

fractional-size violins work: pegs don't shrink proportionally with the instrument.

- Dovetail neck joint: kept exactly as alleycat designed it, just uniformly scaled along with the

body/neck shaft — no redesign, so the same care applies (print the joint test pieces first, use the

"High Tolerance" approach if it's too tight, hand-fit with small files).

## Dimensions (soprano vs. alto)

| | Alto (measured) | Soprano (this remix) |

|---|---|---|

| String length (nut→bridge) | 308.6mm | 285.0mm |

| Total instrument length | 524.9mm | 491.9mm |

| Body max width | 143.4mm | 132.5mm |

| Body max depth | 76.3mm | 70.5mm |

| Body wall thickness (median) | ~4.0mm | ~3.6mm |

| Tuning | G-D-A (¾ violin strings) | D-A-E (½ violin strings) |

## Files

- 01_Soprano_Rebec_Body.stl — bowl body

- 02_Soprano_Rebec_Neck.stl — neck + full-size pegbox + dovetail pin

- 03_Soprano_Rebec_Fingerboard.stl

- 04_Soprano_Rebec_Soundplate.stl — held by string tension, not glued

- 05_Soprano_Rebec_Tailpiece_Nut.stl — glue to soundplate

- 06_Soprano_Rebec_Bridge.stl

- 07_Soprano_Rebec_Tailpiece.stl

- 08_Soprano_Rebec_Nut.stl — glue to fingerboard/neck, small drop only

- A1_Soprano_Rebec_Joint_Test.stl / A2_Soprano_Rebec_Joint_Test.stl — print these first to

test the dovetail fit before committing to the full neck/body print, exactly as alleycat recommends

for the original.

All parts verified watertight (manifold, single body) via trimesh before export.

## Print settings

Carried over from the alto's own instructions, since wall/perimeter counts don't need to change just

because the part is smaller:

- Body: enough perimeters that there's no infill in the bowl walls; 30–40% rectilinear/grid infill,

1mm min top/bottom shell, organic supports.

- Neck: minimum 7 perimeters, 1mm top/bottom shell, 30–40% infill.

- Fingerboard: minimum 3mm top shell; variable layer height recommended on the curved part

(0.05–0.07mm).

- Small parts (nut, bridge, tailpiece, tailpiece nut): print solid, no infill, in the orientation

shown in the alto's original photos.

- Soundplate: print solid, no infill; same orientation as the alto.

- Print slow — limit flow rate to ~8mm³/s for PLA (6mm³/s for PLA-CF) — same as the alto's guidance.

## Hardware

Same as the alto: 3× banjo-style tuners, 4:1 ratio, Ø17mm barrel, Ø9.5mm shaft into a Ø10mm bore,

10.5mm post spacing. ½-size violin strings, tuned D-A-E.

If you cannot find the correct banjo tuners, then try my friction tuners: https://www.printables.com/model/1861581-friction-clamp-pegs

## License

This remix is a derivative of alleycat's Alto Rebec and is shared under the same license,

GNU General Public License v2.0, as required by the original. Attribution: design derived from

"Alto Rebec" by alleycat (https://www.printables.com/model/460663-alto-rebec).

Tags