Capiflexi: Print-in-Place Articulated Capybara with Yuzu (nodding head, multicolor)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Flexi capybara with a yuzu: nodding head, 6 wiggling body joints, 4 legs. One piece, no supports, 4 colours.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 13
- Makes
- 0
- Views
- 32
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Toys & Games
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
The animation (GIF) shows the real motion, rendered from the same 36 poses that were collision-checked in code.
Capiflexi is a print-in-place articulated capybara with a yuzu on its head. It comes off the bed in one piece, already assembled: a nodding head, a neck and six body segments that wiggle like a snake, and four swinging legs. 13 moving parts, no supports, no glue.
Why it is different
Most flexi animals use pins in the middle of each segment, so the body opens big V-shaped gaps when it bends. Here every segment is a crescent that slides along a circular arc. The arc carries a dovetail rail with 45° flanks, so the body stays closed and smooth while each joint turns ±30°, and the segments cannot be pulled apart in any direction.
The head nods on two 50° cones that come out of the neck plates (40° overhang, printable). The back of the skull is cut at 45° from straight under the hinge, so when the head nods up it never digs into the table.
Each leg wraps 240° around a pin on the body. The pin has a 45° bulge and a 45° conical roof, which traps the leg while it swings ±30°.
Real capybara face: high-set eyes, small round ears, a blunt rounded snout with slanted nostrils and a split upper lip, and fur texture all over (strands run along the back and slant down the flanks, so the texture adds no overhangs).
Details
Size: 155 × 78 × 39 mm. Fits the A1 mini bed (175 × 175 mm) straight, with room to spare.
Clearance between moving parts: 0.35 mm everywhere. The first 0.3 mm of every part is pulled in by 0.2 mm, so elephant foot cannot weld the gaps.
Joint arcs: radius 30 mm, segment thickness 10 mm. Rail: 3.7 mm high at the root, 1.8 mm deep.
Neck cones: Ø7.2 mm base. Leg pins: Ø7.2 mm with a Ø10.2 mm bulge.
A small HANMA is inlaid in dark under the belly (reads from below).
A1 mini + AMS lite, 4 colours: caramel brown #a8703f (body), dark brown #3b2a20 (eyes, nostrils, HANMA), yuzu yellow #f2b01e, leaf green #5a9a3c.
Sliced with Bambu Studio, 0.2 mm layers, no supports: 5 h 29 min, 103 g (85.6 + 2.5 + 13.7 + 1.6; the yuzu figure includes most of the purge). About 110 layers have 2 or 3 colours (eyes, ears and yuzu), so expect roughly 50 minutes of filament changes inside that time.
After printing, flex each joint gently a few times. Start with the legs, then the body from the neck backwards, then the head.
How it was checked
Print pose: each of the 13 bodies is one solid and touches the bed. Across all 66 pairs the collision volume is 0 and the smallest gap is 0.350 mm. With 0.05 mm clearance the gap drops to 0.05 mm (control: it would weld).
Motion, 24 positions per joint: the 6 body joints at ±30°, the head from −15° to +30°, and the 4 legs at ±30°. Collision is 0 and the gap is at least 0.348 mm everywhere. The 36 GIF poses, with everything moving at once, also pass (min 0.348 mm). Controls: turning about a pivot moved by 1 mm collides (body 13.9 mm³, head 2.4 mm³, leg 3.8 mm³).
On the table, the head nods from 0° to +30° and its lowest point stays at z = 0.000. Without the 45° cut it would dig 3.3 mm into the table (control).
Trapped: every part moved 1 mm in 26 directions hits its partner. Controls: without the rail a segment slides out 30 mm, without the cones the head comes off, and with the leg pin trimmed straight the leg lifts off.
Overhangs over 46°: 0.00 to 0.67 mm² per part (bed and first-layer relief not counted). With 30° cones instead of 50°: 29.7 mm² (control).
Colours do not overlap. HANMA keeps 100% of its area under a 0.4 mm minimum-width test, and a 0.3 mm line is rejected (control).
About this design
Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.
Español
GIF del movimiento real. Capibara flexi articulado que se imprime de una pieza, ya montado y sin soportes, con un yuzu en la cabeza. Tiene la cabeza que asiente, el cuello y seis segmentos que ondulan como una serpiente (±30° cada junta, con carril en cola de milano en arco) y cuatro patas que giran. 13 piezas móviles con 0,35 mm de holgura. 4 colores AMS, 5 h 29 min, 103 g.
العربية
صورة GIF للحركة الحقيقية. كابيبارا مرنة بمفاصل تطبع قطعة واحدة مركبة جاهزة ودون دعامات، وعلى رأسها ثمرة يوزو. الرأس يومئ، والرقبة وستة أجزاء من الجسم تتموج كالأفعى (±30° لكل مفصل)، وأربع أرجل تتحرك. 13 قطعة متحركة بخلوص 0.35 مم. أربعة ألوان، 5 ساعات و29 دقيقة، و103 غراما.