USB-C Port Adapter for Wenger Pro II 17" Backpack
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Upgrade the Wenger Pro II 17" backpack's USB port to USB-C using a short right-angle extension cable.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 1
- Makes
- 0
- Views
- 21
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Gadgets
- License
- Creative Commons — Attribution — Noncommercial
What it is
A small printed insert that holds the female end of a USB-C extension cable in the USB port slot of the Wenger Pro II 17" Computer Backpack. Plug the other end into a power bank inside the bag and you get a USB-C port on the outside.
Prints in about 14 minutes
Uses 2.5 g of filament
No supports
Nothing to cut or glue: the stock cable slides out and the adapter slides in
What you need
Wenger Pro II 17" Computer Backpack
UseBean Right Angle USB-C Extension Cable, 0.6 ft (USB-C 3.2 male to female, 20Gbps, 4K video)
How it works
Pocket: the connector slides into a pocket from the flat end of the adapter.
Side slot: a 5.75 mm slot runs the full length of one face, so the cable drops in from the side. Nothing has to be threaded through, which matters because the right-angle plug on the other end would not fit through a hole.
Back stop: a wall behind the connector, 2.4 to 4.5 mm thick, keeps the port from being pushed back into the bag when you plug a cable in. The cable exits through a U-shaped channel in that wall.
Dimensions
Overall: 17.6 × 24.75 × 11 mm, one end fully rounded, 1 mm fillets along the sides and rounded end
Connector pocket: 12.5 × 6.7 mm, 19.75 mm deep
Cable slot: 5.75 mm wide
Walls: 2.15 mm above and below the pocket (1.7 mm at the groove), 2.55 mm at the sides
Fit
The pocket is modeled on caliper measurements of this exact cable's female connector housing: 12.3 × 6.5 mm, with flat faces 9.1 mm wide and ends that bulge 1.6 mm, drawn as a spline rather than a plain fillet. Clearance is 0.1 mm per side for a snug fit.
Other USB-C extension cables will fit only if the connector housing is the same size and shape and the cable is thinner than 5.75 mm. Measure yours first.
⚠ Heads up: cosmetic marks
The fit is tight on purpose. Sliding the connector into the adapter can scuff or mark the soft plastic on the cable's connector housing. The marks are cosmetic only and do not affect how the cable works, and the tight fit is what keeps the port from shifting in use. If you want to keep your cable looking new, this may not be the choice for you.
Compatibility
Tested only on the Wenger Pro II 17" Computer Backpack. Other Wenger and SwissGear bags with USB ports may use a different port housing, so I can't confirm fit on those. If you try it on another model, please leave a comment with the result.
Print settings
Printed on a Bambu Lab P1S. The included .gcode.3mf is sliced for the P1S with a 0.4 mm nozzle. For any other printer, slice the STL.
Material: PLA+ (eSUN)
Nozzle: 0.4 mm
Layer height: 0.2 mm (55 layers)
Walls: 2
Top / bottom layers: 5 / 3
Infill: 15% grid
Supports: none
Brim: none
Nozzle / bed: 220 °C / 55 °C on a textured PEI plate
Print time: about 14 minutes
Filament: 2.46 g (0.82 m)
Orientation
Print it with the solid face on the bed and the cable slot facing up, as in the included file. The only overhangs are the two short ledges that close the top of the pocket, and the file prints them without supports.
Installation
Remove the stock cable. Slide the bag's stock USB cable out of the port opening. Store it somewhere safe, such as the bottom of the pocket, in case you ever want to go back to it.
Seat the USB-C cable. Lay the cable into the adapter's slot, then pull it back as far as it will go, until the connector is fully seated in the adapter.
Install the adapter. Slide the cable and adapter into the USB opening in the back. It should sit snugly.