1 / 3
Elegoo Neptune 4 Pro Right-Side Organizer with Hinged Tray Lid — image 1
1 / 3

Elegoo Neptune 4 Pro Right-Side Organizer with Hinged Tray Lid

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Clip-on storage with a hinged tray lid, three bins, a long tool channel and an open upper pocket.

Rating
0 / 5
Likes
0
Downloads
1
Makes
0
Views
9
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution

This organizer clips onto the right side of the printer base, behind the screen. It combines a compartmented lower box, an open upper pocket and a hinged lid that also works as a small tray.

The body and lid have been printed in PETG, assembled and fitted to an Elegoo Neptune 4 Pro. The photos show the actual print. Compatibility with other Neptune models has not been tested.

FEATURES

One-piece body with an integral spring clamping foot and a rear corner stop; no screws, magnets or glue are required. The lower box is 190 mm long and projects 84 mm outward from the printer side. Inside are one long tool channel and three fixed compartments. The open upper pocket holds frequently used items.

The separately printed lid opens toward the printer, with an opening stop at approximately 98 degrees. Its raised top rim keeps small items from rolling off: the main tray rim is 3.8 mm high. The flat underside allows printing directly on the bed, with only small supports near the hinge pins. There is no separate latch holding the lid closed.

FILES

01_Organizer_Body.3mf and 02_Hinged_Tray_Lid.3mf contain the geometry only, for use with your own slicer settings.

03_Organizer_Body_Orca_PETG_04.3mf and 04_Hinged_Tray_Lid_Orca_PETG_04.3mf are prepared OrcaSlicer projects. Open these as projects to retain the orientation, settings, local reinforcement and support painting. Re-slice before printing. All files are in millimeters at 1:1 scale. Print the complete body and lid separately.

PRINTING

PETG, 0.4 mm nozzle. Body: 0.20 mm layers, 3 walls, 15% gyroid infill. Lid: 0.16 mm layers, 4 walls, 15% gyroid infill. Both use a 0.20 mm first layer, 5 top and 5 bottom layers, and an 8 mm brim.

The body project includes local reinforcement with 4 walls and 25% infill at Z0-9 mm and Z46-65 mm, measured from the bed.

Print the body upright, bottom down. Supports are required below the upper pocket and mounting features. The body project has support blockers on the inner hinge-bore faces.

Print the lid flat with its inner face down and tray rim up. Small supports are still required near the hinge pins; no support is needed under the main panel. Rotating the lid onto its long edge adds a large wall of support.

Included support settings: normal automatic / Snug, top gap 0.30 mm, XY gap 0.35 mm and 2 top interface layers.

The supplied PETG preset uses 245 C on the first layer, 250 C afterwards and an 80 C textured PEI bed. Use temperatures and flow settings calibrated for your own filament and printer.

OrcaSlicer estimates including brim and supports: body about 208 g / 13 h 38 min; lid about 43 g / 3 h 29 min. Only about 0.18 g of the lid estimate is support. Actual results depend on your setup.

ASSEMBLY

Let both parts cool, then remove supports and brim. Support removal around the body hinge ears was the most difficult part of the first print: remove it in small pieces and avoid levering against an ear. Clean the pins and bores before assembly.

Hold the lid partly open, around 45 degrees, with its rear end angled slightly outward. Insert the front pin into the single closed front eye. Align the rear end and snap its pins into the rear hinge cups. Check that the lid rotates freely and rests against the opening stop.

Clip the organizer onto the right side of the printer base. The lower foot flexes slightly during installation; the rear corner stop locates the body along the printer side. Check clearance to the screen, rear foot, cables and moving bed on your printer.

LAYOUT NOTES

The dividers are fixed. The compartment proportions are not ideal for every tool collection, so check the layout in your slicer before committing to the full body print. This organizer is intended for light printer accessories such as nozzles, screws, small spare parts, hex keys and USB drives.

CREDITS

The mounting cross-section and spring-clamping principle were adapted from Liberty4Ever's Elegoo Neptune 4 / 4 Pro Waste Bin, published under Public Domain / CC0:

https://www.printables.com/model/611113-elegoo-neptune-4-4-pro-waste-bin

This remix relocates the mount to the right/rear side and adds the compartmented organizer, upper pocket, rear corner stop and hinged tray lid. Thanks to Liberty4Ever for the original mounting design.

Tags