Coffee Tools Organizer - Wall Mount or Countertop
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Compact organizer for a coffee scale, distributor, WDT tools, puck screens and an IKEA TEMPERERAD bag clip.
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 0
- Makes
- 0
- Views
- 31
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Kitchen
- License
- Creative Commons — Attribution
A compact home espresso organizer for a coffee scale, coffee distributor, two WDT tools, two puck screens and an IKEA TEMPERERAD coffee bag clip.
The finished model has been printed successfully without supports and checked with the actual accessories shown in the photos. The pictured print used a brim. Printing without a brim has not yet been tested.
FEATURES
- Angled shelf for the coffee scale, with small upper lateral stops to reduce sideways movement.
- Recessed distributor holder with a front access opening.
- Two WDT recesses, one behind the other.
- Two curved puck-screen slots with oval drain outlets.
- Upward-angled pin for the IKEA TEMPERERAD bag clip.
- Two upper keyhole screw slots and a flat back for mounting tape.
- Four rounded 2 mm feet for countertop placement and drainage clearance.
SIZES AND COMPATIBILITY
Overall: 132 mm wide x 222 mm high x 72 mm deep, including feet.
Coffee scale: 93 x 100 x 21.5 mm, including its rubber pad.
Distributor: 58 mm outer diameter; recess 59.2 mm wide and 15 mm deep. The pictured distributor is about 40 mm tall.
WDT tools: 19 mm diameter x 83 mm high; both recesses are 20 mm wide and 15 mm deep.
Puck screens: 53.5 mm diameter x 0.3 mm thickness. Slot entrances are intentionally wider, approximately 3 and 4 mm, for easy insertion.
Bag clip: IKEA TEMPERERAD, approximately 155 mm long with a 9 mm hanging opening; pin diameter 5 mm.
Compare your tools with these dimensions: similarly named accessories can differ in size.
PRINTING
Print with the large flat back on the build plate, as shown in the photo. The supplied STL and geometry-only 3MF are oriented this way.
Supports: OFF for the demonstrated successful print.
Brim: used on the demonstrated print. A brim-free print has not been verified.
Footprint: 132 x 222 mm; allow extra room if using a brim.
Suggested starting settings: 0.4 mm nozzle, 0.2 mm layers, 4 perimeters and 15-20% infill. Adjust to your printer and filament. No printer-specific G-code is included.
MOUNTING
Use 4 mm screws with non-countersunk heads up to 8 mm. Keyhole entries are 9.5 mm, necks 4.5 mm, horizontal spacing 100 mm. Place over the screw heads and lower by 12 mm into the narrow slots.
The flat back also accepts mounting tape appropriate for your tile and plastic. The installed photo shows the organizer on a tiled kitchen wall.
FILES
Coffee_Tools_Organizer.stl - one printable part, millimeters, flat-back-down orientation.
Coffee_Tools_Organizer.3mf - same geometry and orientation, without printer settings or G-code.
Coffee_Tools_Organizer_Editable.blend - editable Blender scene. Accessory mock-ups are in a separate reference collection; print only the organizer body or use the STL/3MF.
README_EN.txt - dimensions and print notes.
DESIGN
Original design developed from a hand sketch and measurements with AI assistance from Codex. Final geometry was digitally validated, then physically printed and checked with real tools. This independent organizer is compatible with the listed accessories; it is not an IKEA product.
