OPXL5H Spool-O-Matic
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
I designed a solution to place 5 spools on one side of an Original Prusa XL.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 1
- Makes
- 0
- Views
- 20
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Background
I have limited room for my OPXL5H, and have it placed in a closet with easy access to only the left side of the printer. Previously I used various filament dryers to spool filament to the printer. However, the various models all exhibited an annoying tendency for the filament to become stuck on a far inside of the spool while unspooling. It wasn't a tangle/overlap. It's just that the filament closest to the inside of the spool flange was so tightly wedged that it wouldn't release easily. This resulted in the dryer being dragged across the table to the printer and eventually jamming the filament. This resulted in 'air printing'.
The default XL spool holders are designed to be 3 on the left and two on the right, and are positioned in a way that seems to minimize the stuck filament issue. But with no access to the right side I needed a better solution. In addition, the static nature of the default spool holders didn't present a smooth rotation of the spool.
Design
I had some 20x42x12 mm bearings remaining from another project, so I re-purposed them for this project. The current part design is for 1kg Polymaker spools, but the spindles can easily be adapted to fit spools that don't match the Polymaker dimensions (55mm hub, 65mm width). Let me know in comments if you need a custom size and I'll see what I can do. If spools are wider than 65mm then a slightly longer retaining screw may be required, but is easily adapted.
There are 2 different models in this project. The 'upper' frames are designed to mount at the top of the vertical extrusion rails. One nut is placed at the top of the vertical rail and a second nut is placed just above the first on the horizontal rail. At this position there is enough room to add 2 additional spools below it. The 'lower' frame is designed to mount underneath the upper frame. There should be enough room to mount 3 spools at the printer middle.
I designed the frames in 2 pieces to:
Provide a 'stand off' for the frame to clear the XL enclosure frame/housing
Limit issues with support for retaining pins that fit into extrusion rails
There are different frame adapters for upper/lower
I currently have a unified/custom filament sensor assembly with feeds that point to the left (designed when I was using filament dryers as filament feeders). I may revert to a unified sensor assembly with feeds pointing towards the front.
Parts
7 4mm x 20/25 pan head screws
7 4mm spring T nuts
Printing
I used Polymaker PETG for the parts for smoothness and durability.
I used .25 layers and .40 nozzles with the structure profile
I mostly used 30% infill (gyroid) and 3 perimeters. In my experience I've found that gyroid seems to be more durable for parts that might be stressed. I tested this hypothesis with a 25lb pry bar and trying to beat the model to submission.
Supports and needed for the inside spindle holder.
I print a set of spindles for each spool and just leave them on the spool for quick mounting
One idea is to print each set of spindles a specific color for quick identification of the filament
Assembly
The frame adapters are different for upper and lower frames
The bearing is a tight fit on the spindle as there is a minuscule 'shoulder' on the edge of the bearing spindle to hold the bearing in place. It just requires firm seating if your printer tolerances are good
If you're printing with high acceleration on an XL, then the upper filament spools, and the upper frames) may wobble/vibrate a bit. I've found that attaching a bit of medium density foam between the frame and the XL enclosure cover dampens the vibration.
Again, let me know in comments if you need some alterations/enhancements.