Dragino PS-LB Halterung für Brunnenstube / Dragino PS-LB Mount for Spring Chamber
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Halterung Dragino PS-LB: Brunnenstube per LoRaWAN messen | Dragino PS-LB mount: spring chamber level via LoRaWAN
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 12
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Outdoor & Garden
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
🇩🇪 Deutsch
Ich wollte unsere Brunnenstube digital anbinden. Ich will wissen, wie viel Wasser drin ist, wie viel die Quelle nachliefert und wann es knapp wird, ohne jedes Mal den Deckel aufzumachen. Jetzt liegt eine Drucksonde am Boden der Stube. Ihr Kabel läuft durch das Entlüftungsrohr nach draußen zu einem LoRaWAN-Funkknoten, der alle 5 Minuten an Home Assistant sendet. Dort sehe ich Wasserstand, nutzbaren Vorrat und Schüttung, und auch, wie lange der Vorrat noch reicht. Ist der Pegel zu niedrig oder der Überlauf verstopft, bekomme ich eine Push-Nachricht.
Fehlte nur noch eine Möglichkeit, den Funkknoten draußen wetterfest zu montieren. Bohren wollte ich nichts, und die Entlüftung sollte offen bleiben. Daraus sind diese drei Teile entstanden:
Aufsatz: kommt statt der Entlüftungshaube auf das Entlüftungsrohr. Daneben hält er in einem Becher ein HT-Rohr DN 50 als kleinen Mast. Die Luft entweicht nach unten durch einen 1-mm-Ringspalt, so bleiben Regen und Insekten draußen. Das Sondenkabel geht durch ein 7-mm-Loch im Deckel. Der Aufsatz ist zweiteilig und wird mit 6 Schrauben M4 verschraubt, deshalb kann man ihn um das schon verlegte Kabel herum montieren.
Halterung: Auf diese Platte wird der Funkknoten geschraubt. Sie wird mit einer Kappe oben auf das HT-Rohr gesteckt, die das Rohr gleich mit verschließt. Zwei Kabelbinder halten sie gegen Verdrehen.
Haube: schützt vor Sonne, UV und Regen. Sie wird in Nuten aufgeschoben und rastet ein. Unten ist sie offen für Kabel, Kondenswasser und Luft. Um die Taste am Funkknoten zu drücken, ziehe ich die Rastlaschen leicht nach außen und schiebe die Haube nach oben ab.
Verwendete Hardware:
Funkknoten: Dragino PS-LB-I5, 868 MHz (EU868), mit Batterie ER26500 (Li-SOCl₂, 8500 mAh)
Sonde: die zugehörige Tauchsonde von Dragino (Variante I5): 4–20 mA, 0–5 m Messbereich, 5 m Kabel, Edelstahl 316, IP68
Gateway: Dragino LPS8N
Software: ChirpStack als Home-Assistant-Add-on, Daten über MQTT in Home Assistant
Druck: ASA oder PETG, kein PLA. Die Haube am besten hell und ohne Carbon- oder Metallanteil, sonst wird der Funk abgeschirmt. 5 Perimeter, 15 % Infill, 0,2 mm Schichthöhe, keine Stützen. Die STLs liegen schon in Drucklage. Insgesamt etwa 407 g Filament.
Zubehör: 8× M4×20 Edelstahl mit 8 Muttern und 16 Unterlegscheiben, 2 UV-beständige Kabelbinder (7,6–9 mm breit, mindestens 300 mm lang), HT-Rohr DN 50 (bei mir 1,5 m). Das Entlüftungsrohr muss mindestens 14 cm aus dem Boden ragen und fest sitzen, denn es trägt alles allein.
Für dein Rohr anpassen: Mein Entlüftungsrohr hat 37,2 mm Außendurchmesser, und genormt ist da leider nichts. Deshalb entstehen alle Teile aus einem parametrischen Python-Skript (halterung.py). Du trägst deine Rohrmaße oben im Skript ein und erzeugst die STLs mit einem einzigen Befehl neu. Wie das geht, steht Schritt für Schritt in der beiliegenden README.
🇬🇧 English
Title: Dragino PS-LB Mount for Spring Chamber
I wanted to connect our spring chamber to our smart home. I want to know how much water is in it, how much the spring delivers and when it's running low, without lifting the lid every time. Now a pressure probe sits on the chamber floor. Its cable runs out through the vent pipe to a LoRaWAN node, which reports to Home Assistant every 5 minutes. There I can see the water level, the usable reserve and the spring's inflow, plus how long the reserve will last. If the level drops too low or the overflow gets blocked, I get a push notification.
All that was missing was a weatherproof way to mount the node outside. I didn't want to drill anything, and the vent had to stay open. That's how these three parts came about:
Vent adapter: replaces the vent cap on the vent pipe. A cup next to it holds a 50 mm drain pipe (DN 50) as a small mast. Air escapes downward through a 1 mm annular gap, which keeps rain and insects out. The probe cable passes through a 7 mm hole in the top. The adapter comes in two halves bolted together with 6 M4 screws, so you can fit it around a cable that's already installed.
Mount: the node is bolted to this plate. A cap on top slides over the mast pipe and seals it at the same time. Two cable ties stop it from rotating.
Hood: protects against sun, UV and rain. It slides into grooves and snaps in place. The bottom is open for the cable, condensation and airflow. To press the node's button, I pull the snap tabs out slightly and slide the hood up and off.
Hardware used:
Node: Dragino PS-LB-I5, 868 MHz (EU868), with an ER26500 battery (Li-SOCl₂, 8500 mAh)
Probe: Dragino's matching immersion probe (I5 variant): 4–20 mA, 0–5 m range, 5 m cable, 316 stainless steel, IP68
Gateway: Dragino LPS8N
Software: ChirpStack as a Home Assistant add-on, data passed to Home Assistant via MQTT
Printing: ASA or PETG, not PLA. Print the hood in a light colour and without carbon or metal fill, which blocks the radio signal. 5 perimeters, 15 % infill, 0.2 mm layers, no supports. The STLs are already oriented for printing. About 407 g of filament in total.
Hardware for assembly: 8× M4×20 stainless screws with 8 nuts and 16 washers, 2 UV-resistant cable ties (7.6–9 mm wide, at least 300 mm long), 50 mm drain pipe (mine is 1.5 m). The vent pipe must stick out of the ground by at least 14 cm and sit firmly, because it carries everything on its own.
Adapting it to your pipe: My vent pipe is 37.2 mm OD, and unfortunately there's no standard size for these. That's why all parts are generated by a parametric Python script (halterung.py). Enter your pipe sizes at the top of the script and regenerate the STLs with a single command. The included README walks you through it step by step.