Toothbrush Holder That Drains Into the Sink – 4 Brushes, Electric + Manual, No Cup, One Piece
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
One-piece toothbrush holder with no cup: brushes lean in open V-cards and the floor slopes to a spout over the basin.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 0
- Makes
- 0
- Views
- 32
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Bathroom
- License
- Creative Commons — Attribution — Noncommercial
A one-piece toothbrush stand for four brushes in two layouts: family (2 electric + 2 manual) and four manual. It stands on the counter at the basin edge and a short spout reaches over the bowl. Each brush stands in its own open folded "card" (a V in plan) and leans back against it at 6°. There is no cup, so nothing holds the water: the whole top is one floor that falls toward the spout, and water that drips off the heads and runs down the handles is meant to flow out through the spout into the basin.
Validation status (please read): digitally validated only: CAD geometry checks, slicer checks without supports, and computed water-path, lean and stability checks on the 3D model. It has not been physically printed, and not yet tried with water, toothpaste or real brushes. All pictures are 3D renders or diagrams of the model, not photographs.
Features
Water path by design: one floor falls toward one spout (12.5°, steepening to 15° where head drips land). On the 3D model every steepest-descent path on the floor ends at the spout tip, with the stand level and with the counter tilted 1° toward the basin or sideways. No pockets and no drain holes to clog. This is a computed check, not a water test.
Same lean for every handle width: each card touches a brush only in a foot band and a top band, so a straight handle of any width in the slot's range leans the same 6° (measured on the model). Tapered handles lean a little differently: about 4-12° (manual) and 5-8° (electric), computed.
Brushes stand apart: at least 4 mm between the widest handles and at least 5 mm between cards.
Each base rests on a small seat that falls toward the fold, meant to guide the base back into its V.
One part, no supports, no glue, no hardware. It rinses under the tap.
Sizes and which brushes fit
Layout | Slots, left to right | Width x depth (+ spout) x height |
|---|---|---|
Family | manual, electric, electric, manual | 156 x 96 (+15) x 158 mm |
Four manual | 4 x manual | 142 x 96 (+15) x 110 mm |
Slot | Handle / base width | Brush length | Notes |
|---|---|---|---|
Electric | 24-34 mm, at the bottom and at 110-125 mm up | up to 260 mm, up to 150 g | flat bases only; not for slim sonic brushes with a round, test-tube-like base |
Manual | about 5-20 mm | about 150-200 mm | the top band sits 70-85 mm above the base; round tails thinner than about 6 mm stand in the fold itself and lean 1-2° more |
Suction-cup bases are not supported.
Where it fits
A counter or tap deck at least 96 mm deep behind the basin edge. Place the dish front 0-10 mm from the bowl edge so that at least the last 5 mm of the spout, with its drip groove underneath, hangs over the bowl.
Undermount, integrated and wall-hung basins. Not vessel sinks, and not basins with a raised rim, which the spout cannot reach over.
The brush heads stay above the stand's dish; nothing projects over the basin except the empty spout.
Which files?
Ready-to-print PrusaSlicer projects with the settings embedded and sliced to check them: toothbrush-stand_family_PETG and toothbrush-stand_four-manual_PETG. Open, select your printer, slice, print.
STL files for any slicer: toothbrush-stand_family and toothbrush-stand_four-manual. Do not rescale them: the slot sizes are for real brush widths.
model.py: the parametric CadQuery source (Python 3.10+ with cadquery, trimesh, shapely and numpy;
python model.py --preset four_manual). Only the two published layouts were checked; the source also contains other layouts (three manual, two electric, manual + electric, kids') that are NOT checked, and the two-electric layout failed the tipping check.
Print settings
PETG (wet bathroom use); PLA is not recommended.
0.4 mm nozzle, 0.20 mm layers, no supports (every overhang is 45° or less). Flat bottom on the bed, as exported.
3 perimeters, 6 top / 4 bottom layers, 50 % gyroid infill: higher than usual on purpose, because a heavier base resists tipping. The 2 mm cards print solid.
Slicer estimates (not measured prints): family 13.7 h / 271 g on a Prusa MK4S (HF0.4, 0.20 mm SPEED preset) or 27.9 h / 272 g on a slow generic profile; four manual 11.6 h / 232 g or 23.9 h / 233 g. Most of the mass is the heavy base.
Use
Remove any brim and check that the spout tip and the drip groove under it are clean.
Place the stand with the dish front 0-10 mm from the bowl edge and the spout tip over the bowl; the spout position comes first. Where the counter behind the basin is only about 96-105 mm deep, the back can also rest against the wall or backsplash.
Set each brush straight down at the back of its seat; it leans back against the card.
Rinse the stand under the tap now and then. Brush out the bottom of each V with an old toothbrush: the narrow channels beside the manual seats hold a little water and paste.
Stability
The stand is light for its height (about 272 g family, 233 g four manual, as sliced at 50 % infill). Pushing a brush backwards is the gesture that tips it. Computed from the model with the heaviest brushes (150 g electric, 20 g manual):
Layout | Push back at mid-handle | Push back at the tallest head | Empty stand, push at a card top |
|---|---|---|---|
Family | about 2.0 N (200 g of force) | about 1.0 N | about 0.8 N |
Four manual | about 1.6 N | about 0.7 N | about 1.0 N |
Setting a brush down firmly (2 N at 45°, down and back) does not tip it by the calculation (safety factor 1.4 for the family layout, 2.5 for four manual). Set brushes straight down rather than pushing them back; where the counter allows it, the wall behind stops the stand tipping backwards. Brushes lean, they are not clipped: a manual brush whose head is nudged about 2.5 cm forward can fall out toward the basin (an electric brush needs about 6 cm).
Limitations
Not physically printed, and not yet tried with water, toothpaste or real brushes. The water path, lean, fit and stability are computed on the 3D model.
How water behaves on printed layer lines, and how easily paste rinses off, are not yet known.
The centres of gravity of real brushes are assumed (no source publishes them); the stability numbers depend on them.
Brushes are held by their lean only; a nudged manual brush can fall toward the basin.
Not a hygiene or antibacterial product; the only claim is the designed water path. No toothpaste holder.
Pictures
All pictures are 3D renders of the exported model or diagrams made from it, not photographs: the family layout at a basin edge (cover), a staged bathroom scene, the computed water paths, how a handle touches its card, the empty stand and a dimension sheet. Brushes, basin, water and props are generic stand-ins.