Early 1/4 Federal Signal 500-SH/500-SHTT Siren
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Fully functional, accurate, customizable, and weather resistant models of the early variants of the Federal Signal 500!
- Rating
- 0 / 5
- Likes
- 4
- Downloads
- 12
- Makes
- 0
- Views
- 102
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Mechanical Parts
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
OVERVIEW:
First I made the later 500s, and now it's time for the early 500s!
This includes models for all the early (short rotator) versions of the Federal Sign & Signal 500 siren. That includes the 500-SH and 500-SHTT.
With that aside, like the last 500's Printables, here's an image that explains everything you need to know before you build your 500!

PARTS LIST:
MOTOR: https://www.amazon.com/CHANCS-Electric-555-8000RPM-Accessory/dp/B0CW61NGF4/ref
SHAFT COUPLER(S): https://www.amazon.com/12Pcs-3-17mm-Coupling-Connector-Airplane/dp/B0DKT5T64L/ref
ALAN WRENCH:
Any LONG 1.5mm alan wrench will work but the ones that come with the coupler are not long enough. Here's one you can use although feel free to search for another one or style you prefer!
https://www.amazon.com/Dynamite-DYN2814-Hex-Driver-1-5mm/dp/B000BQ1SFE/ref
SLIP RING: https://www.amazon.com/Comidox-CIRCUITSx2A-Capsule-Electrical-Equipment/dp/B07H2SRMXP/ref
THRUST BEARING: https://www.amazon.com/FOCMKEAS-AXK3047-Bearings-Thickness-Industry/dp/B0CY5NSXR9/ref (There are a couple other listings for the thrust bearing you'll need. If you want to look for another, make sure it has a 30mm ID, 47mm OD, and a 4mm thickness!
GEARBOX: https://www.amazon.com/SparkFun-Hobby-Gearmotor-140-Pair/dp/B07JX7MHSL/ref
OR: https://www.amazon.com/Pack-Dual-Shaft-Gear-Motor/dp/B0C448W34R/ref
M3 THREADED INSERTS: https://www.amazon.com/dp/B08BCRZZS3?ref
M2 THREADED INSERTS: https://www.amazon.com/ruthex-Threaded-Insert-pieces-ultrasound/dp/B088QJG676/ref
M3 HARDWARE KIT: https://www.amazon.com/Machine-Assorted-Assortment-Stainless-Threaded/dp/B0DFWYBJJJ/
M2 HARDWARE KIT: https://www.amazon.com/Machine-Assorted-Stainless-Assortment-Threaded/dp/B0DFWXRM21/ref
CASSETT TAPE BELTS: https://www.amazon.com/Recorder-Cassette-Maintenance-Machine-Repeater/dp/B0CZ4549WN/ref
POWER:
BUCK CONVERTER: https://www.amazon.com/dp/B0DFH46JPD?ref=ppx_yo2ov_dt_b_fed_asin_title
SUPER CAPACITORS: https://www.amazon.com/dp/B0DBQYF49G?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1
To wire the supercapacitors, you want to wire them in a series (not parallel!) This diagram shows you how to wire it:

Since the siren is quite big and there's a lot of space inside, you can do a lot of setups. For example, you can solder the supercapacitors directly to the motor terminals, glue them somewhere else in the motor cover, or even put them in the rotator box bottom!
A few things that are really important, you can NOT use a PWM speed controller with supercapacitors!!! You NEED either a power supply or a buck converter (the ones I used are linked!!). Another thing to note is that the voltage coming out of the buck converter has to be wired correctly to the supercapacitors. POLARITY MATTERS!!! Wire the positive coming from the buck to the positive on the supercaps and same with the negative.
And one of the most IMPORTANT THINGS is that you NEED to use a voltage meter to test how much is coming out of your buck before you wire it to the supercaps. The supercaps (when wired in a series) have a max voltage or around 10 volts. If your buck converter is putting MORE than 10 volts out, there is a chance your supercaps will go kaboom!! So make sure you turn the voltage to around ~7.5, then connect the supercaps, then wire it to the siren and tune it to the perfect pitch! The siren shouldn't even need very close to 10 volts to run properly.
INSTRUCTIONS:
First off, you should know what 500 you're planning on making. The SH has it's own core/horn assembly folder for both varients of the horn while the 500-SHTT is in it's own folder!
Start by printing the rotor. It will have a center hole for the shaft coupler to fit in. It should be toleranced to need a hammer to tap itself in but if yours is pretty loose, put a small line of super glue inside the hole (on either side OPPOSITE of the setscrew holes as to not get glue inside) And speaking of the setscrew hole(s), make sure they're aligned with the small holes inside of the rotor so that they line up when the coupler is pressed in otherwise your rotor AND shaft coupler are cooked.

(Photo is from my 1/3 scale Model 2/Thunderbolt rotor but it's the same concept)
If you want to test out the rotor on your motor, refrain from tightening the setscrews a LOT as stressing out the threads and setscrews can give your rotor wobble. Wait to crank it all the way down once you have the stator on there too!
And speaking of the stator, that's the next thing you'll print alongside the stator back ring and the eyebolt bracket. Now.... Like the newer 500-SHTT, one of the main design flaws with the 500 is that once you fully assemble the core, you cannot put the horn on unless you take it apart again. This is due to the fact that the horn attaches from the BACK of the stator so therefore, you can't pull it off without taking other things apart. Because of this, I'd recommend printing your full horn and assembling it as well. All the horns are either a single piece or split into thirds. Weld all the sections together and then weld the horn back ring to the horn from the inside (front). You won't have to worry about alignment unless you're making the 500-SH with the six horn support brackets since the holes need to line up with the intake holes. I'll attach a photo of the correct orientation:

(Remember, if you're not making this kind of horn, you won't need to worry about the alignment.
The whole core/horn assembly goes together as one big sandwich that has to be in a specific order. It's similar between both the SH and SHTT but not the exact same.
This is the assembly of the 500-SH:


This is the stator/motor/motor cover assembly. The motor attaches in with two M3 bolts, the motor cover screws in with four M3 bolts into the threaded inserts on the motor cover itself, and those four outer inserts go in from the back.
Next off, you'll want to attach your horn. I already went over the horn assembly, but it will fit on the back of the stator and screw in with 12 M2 bolts that secure with nuts on the inside of the stator. You'll notice on my photo, I only have six M2 bolts (that's just because I'm broke on hardware right now and didn't have all twelve bolts)


Now that you have your horn on, you'll need to attach the back stator ring. That piece is what goes into the inserts on the back of the stator. You'll also need to put the eyebolt bracket on the top insert and bolt that to the stator as well.

This is what the back should look like!
The last step is flipping it over and attaching your intake! If you're doing the four support design, the intake will attach through the (what would be on an STH-10) horn holes (the tiniest holes on the outer part of the top stator brim) and those will secure with M2 nuts on the back. If you're doing the six bracket design, those will go into six M2 threaded inserts that go on the (what would be STH-10's) intake holes (there are six of them and they're the slightly bigger holes closer to the center of the stator). Remember that for the bracket design, add the brackets on top of the intake before you put a bolt in! Then just bolt them through the side of the horn with nuts or for the four support intake, weld the supports to the outside of the horn.


Now for the 500-SHTT!
Since I didn't actually make one, I'm going to add a screenshot of the model that should explain the process. Essentially you have the core (JUST stator, motor cover, and rotor built (assembled in the same way as the SH's)

and then the horn and back stator ring both bolt together with the bolt holes on the sides of the stator. The horn goes directly on the back of the stator and the back stator ring goes on top of that. Remember to add the eyebolt bracket to the top hole as well since I forgot to include it in the image lol

Now you can go ahead and bolt your intake on to the front, and that's it for your core/horn assembly for the SHTT! That just goes on with four M3 bolts and nuts. And thanks to KansasCitySirens for remaking the horn in blender for me since Tinkercad was REFUSING to export to Fusion! (we love you joe!!!!!)
ROTATOR ASSEMBLY:
For the rotator assembly, I decided (like my other 500's printables) to record a video rather than explaining. This video goes over the rotator assembly, how to attach the core to the rotator, and also how the slip ring is wired:
For the gearbox, drive gear, and pulleys, it's basically the same assembly as my later 500 design. Start by printing the drive gear shaft as well as the drive gear. Sand the smaller nub on the drive shaft just a little bit so the gear firmly fits on, but can also spin itself on the shaft under a lot of load. Next, take your gearbox and press the shaft onto one of the white plastic output shafts. The gearbox fits into the rotator facing backwards with two LONG M3 bolts that go all the way through the holes into the two inserts below like this: (I'd also recommend greasing your drive gear)

This is how the pulleys attach (you'll need another shaft coupler to attach to the back of the motor. Then, you'll thread an M3 bolt all the way through the other side through both ends of the coupler and the plastic pulley and tighten it on the other side with a nut. It's the same design as my Type 1 Allertor so I'll also attach a photo of the Allertor's pulleys.


As for the other pulley, it's just a press fit onto the gearbox motor shaft. Connect the two together with a cassette tape belt (best option) or a rubber band.
FINAL ASSEMBLY:
To finish things off, you'll notice that the back stator ring has holes around the outside. Those are for M2 threaded inserts in order to screw the cover on! The tiny holes around the brim of the top rotator plate are also for M2 screws to secure. However, those ones don't use inserts and just plastic thread themselves in. If you somehow take on and off your cover a billion times and wear out the plastic, you can always put an M2 nut on the bottom to secure it in place!
For the eyebolt, just go to a hardware store and get a small screw-in eyebolt and screw it into the eyebolt bracket through the top with the main back cover on!
For the bottom stand pieces, watch the rotator tutorial if you're confused on the assembly (they attach to the rotator base with four M3 inserts total). For the side panels, those all attach with M2 bolts into inserts in the stand and for the junction box, push it through the hole on the corresponding panel for it (the one with the hole). The junction box cover uses M2 screws that simply plastic thread to hold on.
Your 500 is complete!!!
(I haven't even finished mine yet so I'll have to add a photo later lmao)