Prusa-Style Toy Hammer (One-Piece or Two-Colour Press-Fit, Parametric)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Parametric toy claw hammer for kids: one-piece or two-colour press-fit head and handle. Fit test included.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 1
- Makes
- 0
- Views
- 22
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Toys & Games
- License
- Creative Commons — Attribution — Noncommercial
ABOUT
My kid's toy hammer broke: the striking end snapped off the head, and the handle was long gone. So I modelled a new one: a chunky claw hammer with a curved claw, a V-slot between the claw tips, a striking face on a short neck, and a teardrop-shaped handle that is slim under the head, swells into the grip, and ends in a rounded knob.
There are two ways to print it:
• Two-colour, press-fit: head and handle are separate parts. Print them in different colours and press the handle into the head – no glue, no screws. Mine is black and orange, in the Prusa colours.
• One-piece, single colour: head and handle fused into one part, with a 3 mm fillet at the joint. No assembly, no fit to tune.
SIZING
• Head: 75 × 30 × 31 mm (claw tip to striking face × width × thickness)
• Handle: 18 mm under the head, 26 mm at the widest point of the grip
• Two-part hammer, assembled: about 152 mm long
• One-piece hammer: 155 × 75 × 30 mm
• All three SCAD files are parametric (OpenSCAD Customizer):
– hammer_head.scad: total_len, head_len, head_w, head_t, the claw shape, hole_d and hole_clearance
– handle.scad: pin_d (press fit), handle_len, top_d, max_d, cap_len, taper_shape
– hammer_one_piece.scad: joint_fillet; it reuses the other two files, so keep all three in one folder
FIT TEST
Every printer prints holes a bit differently, so check the press fit before printing the whole handle.
• handle_fit_test.stl has three short pins of the handle top: 13.1, 13.2 and 13.3 mm. The collar height tells them apart: 3 mm = 13.1, 5 mm = 13.2, 7 mm = 13.3.
• Print the head first, then push each pin into the hole from the side with the raised ring.
• The right one goes in with firm hand pressure (or a few light taps) and sits solid, with the collar against the ring. Loose = go bigger; will not go in = go smaller.
• handle.stl has the 13.2 mm pin, which fits on my printer. If another pin fits better, set pin_d in handle.scad and export the handle again (the test pins are always pin_d −0.1 / ±0 / +0.1 mm).
PRINT SETTINGS
Printer: Prusa CORE One, 0.4 mm nozzle
Profile: 0.20mm STRUCTURAL, PETG at 250 °C, bed 85 °C
Material: Buddy Black PETG (head), Prusament PETG orange (handle)
Head (printed together with the fit test):
• Lying on its flat outer side, handle hole vertical
• 2 perimeters, 5/4 top/bottom layers, 15 % infill
• Supports: snug, build plate only – under the claw curve and the striking face
• Head + fit test: ~1 h 17 m, about 25 g
Handle:
• Standing on the flat spot of the rounded end, pin up
• 2 perimeters, 5/4 top/bottom layers, 15 % infill, no supports, no brim
• ~1 h 46 m, about 21 g
One-piece hammer:
• Head lying on its flat outer side, handle pointing straight up
• 8 perimeters, 8/8 top/bottom layers, 20 % infill
• Supports: organic, build plate only
• ~3 h 19 m, about 76 g
TIPS
• Print the fit test with the same filament and settings as the handle; otherwise, the result does not carry over.
• Push the handle in only once or twice – repeated insertions wear the press fit. If it ever gets loose, a drop of CA glue fixes it.
• For the one-piece version, the layers run across the handle, so the joint is its weakest spot. Extra perimeters help, as in the settings above.
FILES
STL: hammer_head, handle (13.2 mm pin), handle_fit_test, hammer_one_piece
SCAD: hammer_head, handle, hammer_one_piece (parametric source, keep together)
3MF: PrusaSlicer projects with the settings above
Designed in OpenSCAD with AI assistance (Claude Code).